An inspection of this unit should be made
periodically, consisting of, but not limited to, all
mounting, wiring, and the condition of all
components.
Clean the plastic parts of this unit with a soft, clean,
dump cloth.
This unit should be tested at least once per year for
proper performance and operation.
This unit is designed to be incorporated into an
overall alarm system. As it is part of the system
ALEPH
cannot assume responsibility for theft or
damage if the system fails to operate.
MW DETECTOR operation trouble.
Mode selection switch #5 is PIR MODE only.
Unsuitable adjusting the detection zone.
LED mode selection switch #4 is OFF.
Polarity connection may be reversed.
No input power or voltage is too low.
This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, used and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, these is no guarantee that
interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
The user should not modify or changes this equipment without written approval from ALEPH.
Modification could void authority to use this equipment.
Do not touch the
MW DETECTOR.
Inspection:
Cleaning:
Testing:
Note:
MW LED stays lit continously.
LED indicator does not blink.
LED's indicator does not turn on.
Dose not power up.
Problem
TAMPER
1.
Remove cover by looseing the screw on the
bottom of the unit.
If you have any questions about this product please contact
ALEPH
or
your nearest dealer.
Mode selection switch #5 is PIR MODE only.
Mode selection switch #5 is DUAL MODE.
Adjust the detection zone.
Adjust mode selection switch #4 to LED ON.
Adjust the polarity.
Supply the proper voltage (9.5 to 16 VDC).
Cause
Remedy
SPARE
N.C.
N.O.
N.C.
N.O.
POWER
Do not touch the
MW DETECTOR.
NIPPON ALEPH CORPORATION
1-28-52 Komaoka, Tsurumi-ku, Yokohama, Japan
Tel:
(045)575-1111 Fax:
(045)580-1676
URL http:
//www.nippon-aleph.co.jp/ e-mail:
ALEPH INTERNATIONAL CORPORATION
1026 Grisworld Avenue, San Fernando, California 91340, U.S.A.
Tel:
(818)365-9856 Fax:
(818)365-7274
URL http:
//www.aleph-USA.com/ e-mail:
ALEPH EUROPE LTD.
1 Newton Close, Park Farm Industrial Estate, Wellingborough, Northhamptonshire,
NN8 3UW, England
Tel:
(0933)679600 Fax:
(0933)401165
URL http:
//www.alepheurope.com/ e-mail:
ALEPH Central - Eastern Europe, LLC
Lopuszanska 53/010 Warsaw, Poland
Tel:
+48 22 868 0414 Fax:
+ 48 22 868 0413
URL http:
//www.aleph-cee.com/ e-mail:
＋ −
All wiring must be in accordance with
NEC,NFPA70.
9. FCC STATMENT
10. TROUBLE SHOOTING
11. TESTING and MAINTENANCE
2.
Remove the printed circuit board by loosing
the screw on it.
3.
Use the two screws supplied with the unit to
attach the unit to the wall or corner.
4.
Return the printed circuit board that was
removed in "3" above, to its original position
and then tighten the screw.
5.
Wiring Diagram
6.
To attach cover, hook upper part and push
down, then tighten screw at bottom of the
unit.
8. INSTALLATION