Alemite 7234-B Скачать руководство пользователя страница 1

 

Service Guide

 

Alemite Corporation

PO Box 473515, Charlotte, North Carolina 28247-3515

 

Copyright 

 

© 

 

1997 by Alemite Corporation

This document contains confidential information that is the property of Alemite Corporation

 

670453

 

and is not to be copied, used, or disclosed to others without express written permission.

 

Revision (7-97)

SER 7234-B

 

7234-B
7235-B

 

3-7/8 "

(9.8 cm)

7 " (17.8 cm)

7-7/8 "

(20 cm)

19 " (48.3 cm)

Dia.

21"

(53.3 cm)

17/32 " (13.5 mm) Dia.

 

Figure 1

 

Heavy-Duty Hose Reels Models 7234-B and 7235-B

 

Description

 

Caution

 

These reels must be ceiling mounted at a
height no greater than 16 feet (4.9 m) from

 

the floor to comply with the warranty.

 

Hose reel Models 7234-B and 7235-B are 

designed to be mounted to the wall, ceiling, or floor. 
They can also mount to truck beds.

The reels mount as a single unit or in banks of as 

many as required. Banked reels should be a 
minimum of 9 " (23 cm) apart on center. For ease in 
reel maintenance, a space of up to 15 " (38 cm) is 
recommended. See 

 

Figure 6

 

.

Each model reel is spring-powered and self-

retracting. A latch locks the reel once the required 
length of hose is released. A pull releases the latch 
and allows the hose to retract onto the reel.

 

Models 7234-B and 7235-B

 

Model 7234-B contains a high-pressure swivel 

assembly. This swivel is designed to dispense 
grease from either 1/4 " or 3/8 " ID two-wire braid 
delivery hose.

A medium-pressure swivel assembly is included 

with Model 7235-B. Free-flowing lubricants such as 

 

Heavy-Duty Hose Reels

 

Accessories

 

Material Delivery Hoses

 

Reel

Model

High-Pressure Material Delivery Hose

Medium-Pressure Material 

Delivery Hose

Low-Pressure Air and Water 

Delivery Hose

1/4 " ID Two-Wire Braid

3/8 " ID Two-Wire Braid

1/2 " ID Single-Wire Braid

3/8 " ID Fabric-Reinforced

 

7234-B

317874-30, 317874-50

317870-50

7235-B

317856-20, 317856-30,

317856-40, 317856-50

317803-25, 317803-30,

317803-40, 317803-50

Delivery hose length is designated by the dash number. 

 

Example

 

: 317874-30 is 30 feet long.

 

motor and gear oil, and automatic transmission fluid are 
dispensed from 1/2 " ID single-wire braid delivery hose. Air and 
water is transported through 3/8 " fabric-reinforced hose.

Содержание 7234-B













Отзывы: