Alemite 7175-R4 Скачать руководство пользователя страница 1

Страница: 1 / 30

Service Guide

SER 7175-R4

7175-R4

Alemite, LLC

167 Roweland Drive, Johnson City, Tennessee 37601

www.alemite.com

2011 by Alemite, LLC

This document contains confidential information that is the property of Alemite, LLC

396128

and is not to be copied, used, or disclosed to others without express written permission.

Revision (2-13)

NOTE

: For Table of Contents and

List of Illustrations, see Page 2.

Description

The major components of the 7175-R4

mobile “Rockcrusher” grease pump consist of a:

• 40 pound (18.2 kg) capacity container
• pressure switch controlled drive motor
• helix arm/blade and helicoid flight

priming mechanism*

• high-pressure control valve with z-swivel

and 10 foot (3 m) hose assembly

The pump delivers 14 ounces (0.40 kg) of

NLGI No. 1 grease [at 70 F (21 C)] each minute.
Heavy fibrous grease is pumped at a rate of
5-1/2 ounces (0.16 kg) per minute.

Pressure Switch

A pressure switch maintains lubricant

pressure between 3500 and 5000 psi
(241-345 Bars). This switch assembly acts as
the on/off switch during control valve operation.

Emergency Bypass System

A pressure relief valve operates as a back-up

to the pressure switch.

* This is a positive-feed design that

dispenses heavy grease at low temperatures.

High-Pressure Grease Pump

Bleed/Prime Assembly

This bleeder allows the pump to be primed for initial start-up.

Figure 1

High-Pressure Grease Pump Model 7175-R4

Specifications

Sump

Capacity

Gear Oil

Ounces

Liter

0.95

SAE 80W-90 (GL-5)

Motor

Size

Maximum
Amperage

RPM

(Full Load)

Volts

3/4

0.56

12,000

120 @ 60 Hz

Table 1

High-Pressure Grease Pump Model 7175-R4 Specifications

Содержание 7175-R4































Результаты поиска

Содержание 7175-R4

Отзывы:

Похожие инструкции для 7175-R4

Бренды по названию

Популярные бренды

Alemite 7175-R4, Руководство по обслуживанию

Результаты поиска

Содержание 7175-R4

Отзывы:

Похожие инструкции для 7175-R4

Бренды по названию

Популярные бренды