Alcatel OneTouch Home H200 Скачать руководство пользователя страница 15

User Manual of Onetouch-H200 3G Router 

12 

Domain 

Description 

Connection Mode 

  Auto Connect: when the user chooses 

“Auto 

Connect

”, the system will connect automatically. If 

disconnected by other reason, the system will try to 

re-connect every 10 seconds. If the user pay monthly 

for the service, it is recommended to adopt this mode. 

  Dial on Demand: when the user choose 

“Dial on 

Demand

”, if there is any request for visiting the 

internet, the system will dial up automatically. If 

non-operation during the set idle timeout, the system 

will disconnect by itself. This mode is suitable for user 

who pays according time. 

  Manually Connect: when the user chooses 

“Manually 

Connect

”, he should dial up manually. 

Idle  Timeout  (In 

minutes) 

If stand by time reaches the set value, the connection  will 

be cut. 

Domain 

Name 

Server 

(DNS) 

Address 

Input the DNS provided by ISP. If you ISP didn

’t provide it, 

please choose 

“Get Automatically From ISP”. 

Primary DNS 

If necessary, input IP address of primary DNS. 

Second DNS 

If ISP provides another DNS, input the IP address here. 

Содержание OneTouch Home H200


















Отзывы: