OAW-IAP220 Series Instant Access Point
Installation Guide
The Alcatel-Lucent OAW-IAP224 and OAW-IAP225 Instant wireless access points
support the IEEE 802.11ac standard for high-performance WLAN. This access
point uses MIMO (Multiple-in, Multiple-out) technology and other high-
throughput mode techniques to deliver high-performance, 802.11n 2.4 GHz and
802.11ac 5 GHz functionality while simultaneously supporting existing legacy
wireless services. The OAW-IAP220 Series access point works only in
conjunction with a virtual controller.
The Alcatel-Lucent OAW-IAP220 Series access point provides the following
capabilities:
Wireless transceiver
Protocol-independent networking functionality
IEEE 802.11a/b/g/n/ac operation as a wireless access point
IEEE 802.11a/b/g/n/ac operation as a wireless air monitor
Compatibility with IEEE 802.3at PoE+ and 802.3af PoE
Package Contents
OAW-IAP224 or OAW-IAP225 access point
9/16" and 15/16” Ceiling Rail Adapters
Alcatel-Lucent Instant Quick Start Guide
Installation guide (this document)
OAW-IAP220 Series Hardware Overview
Figure 1
LEDs
LEDs
The OAW-IAP220 Series is equipped with five LEDs that indicate the status of the
various components of the AP.
External Antenna Connectors
The OAW-IAP224 is equipped with three external antenna connectors. The
connectors are labeled ANT0, ANT1, and ANT2, and correspond to radio chains
0, 1, and 2.
Figure 2
External Antenna Connectors (OAW-IAP224 only)
Figure 3
Bottom Panel
USB Interface
The OAW-IAP220 Series is equipped with a USB interface for connectivity with
cellular modems.
Console Port
The serial console port allows you to connect the AP to a serial terminal or a
laptop for direct local management. This port is an RJ-45 female connector with
the pinouts described in
Figure 4
. Connect it directly to a terminal or terminal
server using an Ethernet cable.
Figure 4
Serial Port Pin-Out
Ethernet Ports
OAW-IAP220 Series is equipped with two10/100/1000Base-T (RJ-45) auto-
sensing, MDI/MDX wired-network connectivity port. These ports support IEEE
802.3af and 802.3at Power over Ethernet (PoE) compliance, accepting 48 VDC
(nominal) as a standard defined Powered Device (PD) from a Power Sourcing
Equipment (PSE) such as a PoE midspan injector, or network infrastructure that
supports PoE.
The 10/100/1000 Mbps Ethernet ports are on the bottom of the AP. These ports
have RJ-45 female connectors with the pin-outs shown in
Figure 5
.
Figure 5
Gigabit Ethernet Port Pin-Out
Kensington Lock Slot
The OAW-IAP220 Series is equipped with a Kensington security slot for
additional security.
Reset Button
The reset button can be used to return the AP to factory default settings. To reset
the AP:
1. Power off the AP.
2. Press and hold the reset button using a small, narrow object, such as a
paperclip.
3. Power-on the AP without releasing the reset button. The power LED will
flash within 5 seconds.
4. Release the reset button.
The power LED will flash again within 15 seconds indicating that the reset is
completed. The AP will now continue to boot with the factory default settings.
DC Power Socket
If PoE is not available, an optional Alcatel-Lucent AP AC-DC adapter kit (sold
separately) can be used to power the OAW-IAP220 Series.
Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used
to power this device, as long as it complies with all applicable local regulatory
requirements and the DC interface meets the following specifications:
12 VDC (+/- 5%)/18W
Center-positive 1.7/4.0 mm circular plug, 9.5 mm length
Power Modes
The OAW-IAP220 Series can operate in two power modes. The AP’s mode is not
configurable and is determined by the AP based on the amount of power
available. The two modes are:
Full Power: The AP is receiving power from an 802.3at PoE source or is
powered using the optional AC-DC adapter kit. In this mode, all AP
functionality is available.
PoE Power Saving: The AP is receiving power from an 802.3af PoE source. In
this mode, the AP has limited functionality: the Ethernet port not connected
to the PoE source is disabled, the USB port is disabled, the AP operates in
1x3 RF chain for 2.4 GHz, and the AP operates in 2x3 RF chain for 5 GHz.
Before You Begin
AP Pre-Installation Checklist
Before installing your OAW-IAP220 Series AP, ensure that you have the
following:
CAT5e or CAT6 UTP cable of required length
One of the following power sources:
IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The
POE source can be any midspan power source equipment (PSE) device
Alcatel-Lucent AP AC-DC adapter kit (sold separately)
Summary of the Setup Process
Successful setup of an OAW-IAP220 Series access point consists of four tasks,
which must be performed in this order:
1. Identify the specific installation location for each AP.
2. Install each AP.
3. Verify post-installation connectivity.
4. Configure the virtual controller. Refer to the
Alcatel-Lucent Instant Quick
Start Guide.
Identifying Specific Installation Locations
You can mount the OAW-IAP220 Series access point on a wall or on the ceiling.
Use the AP placement map generated by Alcatel-Lucent’s RF Plan software
application to determine the proper installation location(s). Each location
should be as close as possible to the center of the intended coverage area and
should be free from obstructions or obvious sources of interference. These RF
absorbers/reflectors/interference sources will impact RF propagation and
should have been accounted for during the planning phase and adjusted for in
RF plan.
Identifying Known RF Absorbers/Reflectors/Interference
Sources
Identifying known RF absorbers, reflectors, and interference sources while in
the field during the installation phase is critical. Make sure that these sources are
taken into consideration when you attach an AP to its fixed location. Examples
of sources that degrade RF performance include:
Cement and brick
Objects that contain water
Metal
Microwave ovens
Wireless phones and headsets
Installing the AP
Using the Ceiling Rail Adapter
The OAW-IAP220 Series ships with two ceiling rail adapters for 9/16” and 15/16”
ceiling rails. Additional wall mount adapters amd ceiling rail adapters for other
rail styles are available as accessory kits.
1. Pull the necessary cables through a prepared hole in the ceiling tile near
where the AP will be placed.
2. Place the adapter against the back of the AP with the adapter at an angle of
approximately 30 degrees to the tabs (see
Figure 6
).
3. Twist the adapter clockwise until it snaps into place in the tabs (see
Figure
6
).
The OAW-IAP220 Series requires Alcatel-Lucent Instant 4.0 or later.
Inform your supplier if there are any incorrect, missing, or damaged parts. If
possible, retain the carton, including the original packing materials. Use
these materials to repack and return the unit to the supplier if needed.
Table 1
OAW-IAP220 Series Series LED Meanings
LED
Color/State
Meaning
PWR
Off
No power to AP
Red
Initial power-up
Green - Flashing
AP booting
Green - Steady
AP ready
Orange
AP operating in PoE Power Saving Mode
ENET0, ENET1
Off
Ethernet link unavailable
Amber - Steady
10/100Mbps Ethernet link established
Green - Steady
1000Mbps Ethernet link established
Flashing
Ethernet link activity
5GHz
Off
5GHz radio disabled
Amber - Steady
5Ghz radio enabled in non-HT WLAN mode
Green - Steady
5Ghz radio enabled in HT WLAN mode
Flashing - Green
5Ghz Air or Spectrum Monitor
2.4GHz
Off
2.4GHz radio disabled
Amber - Steady
2.4Ghz radio enabled in non-HT WLAN
mode
Green - Steady
2.4Ghz radio enabled in HT WLAN mode
Flashing - Green
2.4Ghz Air or Spectrum Monitor
2.4GHz
5GHz
ENET1
ENET0
PWR
The USB interface is disabled when the OAW-IAP220 Series is powered
from 802.3af PoE.
When operating on 802.3af, only the port connected to power is
usable. For example, if the source of power is connected to ENET
0, ENET 1 will not work.
ANT0
ANT2
ANT1
56V
350mA
Kensington Lock
USB Interface
Console Port
Ethernet Ports
DC Power Socket
Reset Button
Serial
Console Port
1
2
3
4
5
6
7
8
TxD
GND
RxD
RJ-45 Female
Pin-Out
Direction
Input
Output
GND
FCC Statement:
Improper termination of access points installed in the
United States (non-US model Regulatory Domain model/s) will be in
violation of the FCC grant of equipment authorization. Any such willful or
intentional violation may result in a requirement by the FCC for immediate
termination of operation and may be subject to forfeiture (47 CFR 1.80).
EU Statement:
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands.
Please refer to the
Alcatel-Lucent Instant User Guide
for details on
restrictions.
Produit réseau local radio basse puissance operant dans la bande
fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au
Alcatel-Lucent
Instant User Guide
pour les details des restrictions.
Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet.
Weitere Informationen bezlüglich Einschränkungen finden Sie im
Alcatel-
Lucent Instant
User Guide.
Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare
riferimento alla
Alcatel-Lucent Instant
User Guide
per avere informazioni
detagliate sulle restrizioni.
1000Base-T Gigabit
Ethernet Port
RJ-45 Female
Pin-Out
Signal Name
1
2
3
4
5
6
7
8
BI_DC+
BI_DC-
BI_DD+
BI_DD-
BI_DA+
BI_DA-
BI_DB+
BI_DB-
Function
Bi-directional pair +C, POE Positive
Bi-directional pair -C, POE Positive
Bi-directional pair +D, POE Negative
Bi-directional pair -D, POE Negative
Bi-directional pair +A, POE Negative
Bi-directional pair -A, POE Negative
Bi-directional pair +B, POE Positive
Bi-directional pair -B, POE Positive
Alcatel-Lucent, Inc., in compliance with governmental requirements, has
designed the OAW-IAP220 Series access points so that only authorized
network administrators can change the settings. For more information
about AP configuration, refer to the
Alcatel-Lucent Instant Quick Start
Guide and Alcatel-Lucent Instant User Guide
.
Access points are radio transmission devices and as such are subject to
governmental regulation. Network administrators responsible for the
configuration and operation of access points must comply with local
broadcast regulations. Specifically, access points must use channel
assignments appropriate to the location in which the access point will be
used.
Service to all Alcatel-Lucent Networks products should be performed by
trained service personnel only.
Make sure the AP fits securely on the ceiling tile rail when hanging
the device from the ceiling, because poor installation could cause it
to fall onto people or equipment.
