Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 95

Страница: 95 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 95

Configuration Process Overview

Figure 25

displays the process to provision chassis slots, line cards, MDAs, and ports.

Figure 25: Slot, Card, MDA, and Port Configuration and Implementation Flow

TURN UP

DESIGNATE THE SPECIFIC MDA TYPE FOR THE SLOT

START

CARD

CHASSIS

MDA

PORT

IDENTIFY PORT TO CONFIGURE

CONFIGURE LAG ATTRIBUTES (optional)

CONFIGURE NETWORK AND ACCESS PORTS

SPECIFY CHASSIS SLOT

DESIGNATE THE SPECIFIC CARD TYPE FOR THE SLOT

SLOT

LAG

CONFIGURE PORT PARAMETERS

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды