Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 91

MTU Configuration Guidelines

Observe the following general rules when planning your service and physical MTU
configurations:

•

The 7750 SRmust contend with MTU limitations at many service points. The physical
(access and network) port, service, and SDP MTU values must be individually defined.

•

Identify the ports that will be designated as network ports intended to carry service traffic.

•

MTU values should not be modified frequently.

•

MTU values must conform to both of the following conditions:

→

The service MTU must be less than or equal to the SDP path MTU.

→

The service MTU must be less than or equal to the access port (SAP) MTU.

Default MTU Values

displays the default MTU values which are dependent upon the (sub-) port type, mode,

and encapsulation.

*The default MTU for Ethernet ports other than Fast Ethernet is actually the lesser of 9212 and
any MTU limitations imposed by hardware which is typically 16K.

Table 18: MTU Default Values

Port Type

Mode

Encap Type

Default

(bytes)

Ethernet access

null

1514

Ethernet access

dot1q

1518

Fast Ethernet

network

—

1514

Other Ethernet

network

—

9212*

SONET path or TDM channel

access

BCP-null

1518

SONET path or TDM channel

access

BCP-Dot1q

1522

SONET path or TDM channel

access

IPCP

1502

SONET path or TDM channel

network

—

9208

SONET path or TDM channel

access

frame-relay

1578

SONET path or TDM channel

access

atm

1524

«
...
89
90
91
92
93
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Бренд: WAGO Страницы: 2

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: JUMO Страницы: 60

Бренд: Ubiquiti Страницы: 23

802.11a/b/g SDIO WiFi Module SDM3100

Бренд: Abocom Страницы: 14

ipRocketLink IAD 3086

Бренд: Patton electronics Страницы: 12

Бренд: Zoom Страницы: 2

Бренд: Xantech Страницы: 6

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

Бренд: EMC Страницы: 88

Бренд: ZyXEL Communications Страницы: 191

IntraSwitch 5324MT

Бренд: Asante Страницы: 2

Бренд: Axis Страницы: 64

Бренд: SHOWTEC Страницы: 15

OmniSwitch 6624

Бренд: Alcatel Страницы: 546

ControlCenter-IP 2.0

Бренд: G&D Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды