Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 444

Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 49

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 49

displays bits 5-8 of a K1 byte and K2 Bits 1-4 and the channel number code assignments.

K2 Byte

The K2 byte is used to indicate the bridging actions performed at the line-terminating equipment
(LTE), the provisioned architecture and mode of operation.

The bit assignment for the K2 byte is listed in

.

Table 13: K1 Byte, Bits 5-8 (and K2 Bits 1-4), Channel Number Code Assignments

Channel Number

Code

Channel and Notes

0

Null channel.
SD and SF requests apply to conditions detected on the protection line.
For 1+1 systems, Forced and Request Switch requests apply to the
protection line.
Only code 0 is used with Lockout of Protection request.

1-14

Working channel.
Only code 1 applies in a 1+1 architecture.
Codes 1 through n apply in a 1:n architecture.
SD and SF conditions apply to the corresponding working lines.

15

Extra traffic channel.
May exist only when provisioned in a 1:n architecture.
Only No Request is used with code 15.

Table 14: K2 Byte Functions

Bits 1-8

Function

1-4

Channel number. The 7750 SR supports only values of 0 and 1.

5

0 Provisioned for 1+1 mode.
1 Provisioned for 1:n mode.

6-8

111     Line AIS
110     Line RDI
101     Provisioned for bi-directional switching
100     Provisioned for uni-directional switching
011     (reserved for future use)
010     (reserved for future use)
001     (reserved for future use)
000     (reserved for future use)

«
...
47
48
49
50
51
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов