Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 267

Страница: 267 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 267

ingress

Syntax

ingress

Context

config>port>sonet-sdh>path>atm>ilmi

Description

This command enables the context to configure ingress traffic attributes for the ILMI link.

traffic-desc

Syntax

traffic-desc

traffic-desc-profile-id

no traffic-desc

Context

config>port>sonet-sdh>path>atm>ilmi>egress
config>port>sonet-sdh>path>atm>ilmi>ingress

Description

This command associates an ATM traffic descriptor profile to an ILMI link. It is recommended to

change this to the traffic profile as defined in the ILMI specification.

Default

atm-td-profile 1

Parameters

traffic-desc-profile-id —

Specifies an existing ATM traffic descriptor profile. Traffic descriptor pro-

files are configured in the

config>qos>atm-td-profile

context.

Values

1 — 1000

keep-alive

Syntax

keep-alive

[

poll-frequency

seconds

] [

poll-count

value

]

[test-frequency

seconds

]

no keep-alive

Context

config>port>sonet-sdh>path>atm>ilmi

Description

This command configures keepalive parameters to monitor ILMI link connectivity.

The

form of this command resets the devault values on an ILMI link.

Last Config Change: 03/29/2007 20:35:19 Poll Count:4

Poll Freq:

5 Test Freq: 1

Parameters

poll-frequency

seconds

—

Specifies the amount of time, in seconds, between successive

transmissions of ILMI messages on this interface for the purpose of detecting the establishment
of ILMI connectivity.

Values

1 — 255

poll-count

value

—

Specifies the number of consecutive polls on this interface for which no ILMI

response message is received before ILMI connectivity is declared lost.

Values

1 — 255

Содержание 7750 SR OS





























































































































































































































































































































































































































































Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

Результаты поиска

Содержание 7750 SR OS

Отзывы:

Похожие инструкции для 7750 SR OS

Бренды по названию

Популярные бренды