manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Руководство по настройке интерфейса

"Alcatel-Lucent 7750 SR OS - руководство по настройке интерфейса, доступное для бесплатного скачивания на нашем сайте. Это подробное руководство поможет настроить ваше устройство быстро и эффективно. Скачайте его прямо сейчас с manualshive.com и ознакомьтесь с функционалом продукта."

Поделиться
Скачать
background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 203

General Port Commands

port

Syntax

port

 {

port-id

 | 

bundle-id

 | 

aps-id 

| 

bpgrp-id

}

no port 

{

bundle-id

 | 

aps-id

 | 

bpgrp-id

}

Context

config

Description

This command enables access to the context to configure ports, multilink bundles, and bundle 
protection groups (BPGs). Before a port can be configured, the chassis slot must be provisioned with 
a valid card type and the MDA parameter must be provisioned with a valid MDA type. (See 

card

 and 

mda

 commands.)

Default

No ports are configured. All ports must be explicitly configured and enabled.

Parameters

port-id — 

Specifies the physical port ID in the 

slot/mda/port 

format.

bundle-id — 

Specifies the multilink bundle to be associated with this IP interface. The command syn-

tax must be configured as follows: 

Syntax

: bundle-

type

-

slot/mda.bundle-num

bundle

-

ppp

-

slot/mda.bundle-num 

(Creates a multilink PPP bundle.)

bundle

-

ima

-

slot/mda.bundle-num

 (Creates an IMA bundle.)

bundle

: keyword

slot

: 

IOM/MDA slot numbers

bundle-num

: 

1 — 256

For example:
router1>config# port bundle-ppp-5/1.1 (multilink PPP bundle)
router1>config# port bundle-ima-5/1.2 (IMA bundle)

aps-id — 

This option configures APS on un-bundled SONET/SDH ports. All SONET-SDH port 

parameters, with certain exceptions, for the working and protection circuit ports must be 
configured in the

 config>port>aps-

group-id

 

context. The working and protection circuit ports 

inherit all those parameters configured. The exception parameters for the working and protect 
circuits can be configured in the 

config>port>sonet-sdh

 context. Exception list commands 

include:

clock-source
[no] loopback
[no] report-alarm
section-trace
[no] threshold

When an 

aps-

group-id

 is created all applicable parameters under the port CLI tree (including 

parameters under any submenus) assume 

aps-

group-id

 defaults, or when those are not explicitly 

specified, default to SONET/SDH port defaults for any SONET port.

.All but a few exception SONET/SDH parameters for the working channel port must be 
configured in the 

config>port>aps>sonet-sdh

 context. The protection channel inherits all the 

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Бренд: D-Link Страницы: 38
D-Link DWL-3150 Install Manual preview
DWL-3150
Бренд: D-Link Страницы: 8
D-Link DSS-8+ Manual preview
DSS-8+
Бренд: D-Link Страницы: 22
D-Link DSS-5+ Manual preview
DSS-5+
Бренд: D-Link Страницы: 20
D-Link DSS-24+ Technical Specifications preview
DSS-24+
Бренд: D-Link Страницы: 2
D-Link DSS-24+ Manual preview
DSS-24+
Бренд: D-Link Страницы: 16
D-Link DI-804V Quick Install Manual preview
DI-804V
Бренд: D-Link Страницы: 12
D-Link DIR-615 - Wireless N Router Installation Manual preview
DIR-615 - Wireless N Router
Бренд: D-Link Страницы: 13
D-Link Cobra DSL-5300 User Manual preview
Cobra DSL-5300
Бренд: D-Link Страницы: 124
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Бренд: D-Link Страницы: 6
D-Link 2Voice + 4SW VoIP Router DVG-1402S User Manual preview
2Voice + 4SW VoIP Router DVG-1402S
Бренд: D-Link Страницы: 57
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Бренд: D-Link Страницы: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 97
D-Link SharePort DIR-825 Quick Start Manual preview
SharePort DIR-825
Бренд: D-Link Страницы: 2
D-Link Amplifi DIR-645 Quick Installation Manual preview
Amplifi DIR-645
Бренд: D-Link Страницы: 28
Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Бренд: Panasonic Страницы: 4
Cambium Networks PTP 550 Series Quick Start Manual preview
PTP 550 Series
Бренд: Cambium Networks Страницы: 68

Бренды по названию

Популярные бренды

Загрузить еще бренды