Alcatel-Lucent 7750 SR OS Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 444

background image

Configuration Commands

Page 190

7750 SR OS Interface Configuration Guide

MDA Commands

mda

Syntax

mda

mda-slot

no mda

mda-slot

Context

config>card

Description

This mandatory command enables access to a card’s MDA CLI context to configure MDAs.

Default

No MDA slots are configured by default.

Parameters

mda-slot —

The MDA slot number to be configured. Slots are numbered 1 and 2. On vertically

oriented slots, the top MDA slot is number 1, and the bottom MDA slot is number 2. On
horizontally oriented slots, the left MDA is number 1, and the right MDA slot is number 2.

Values

1, 2

mda-type

Syntax

mda-type

mda-type

no mda-type

Context

config>card>mda

Description

This mandatory command provisions a specific MDA type to the device configuration for the slot.
The MDA can be preprovisioned but an MDA must be provisioned before ports can be configured.
Ports can be configured once the MDA is properly provisioned.

A maximum of two MDAs can be provisioned on an IOM. Only one MDA can be provisioned per
IOM MDA slot. To modify an MDA slot, shut down all port associations.

An MDA can only be provisioned in a slot if the MDA type is allowed in the
MDA slot. An error message is generated when an MDA is provisioned in a slot where it is not
allowed.

A medium severity alarm is generated if an MDA is inserted that does not match the MDA type
configured for the slot. This alarm is cleared when the correct MDA is inserted or the configuration is
modified.

A high severity alarm is raised when an administratively enabled MDA is removed from the chassis.
This alarm is cleared if the either the correct MDA type is inserted or the configuration is modified. A
low severity trap is issued if an MDA is removed that is administratively disabled.

An alarm is raised if partial or complete MDA failure is detected. The alarm is cleared when the error
condition ceases.

«
...
188
189
190
191
192
...
»

Содержание 7750 SR OS





























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7750 SR OS

Бренд: Vonets Страницы: 8

Бренд: NetBurner Страницы: 15

ConnectX-3 Pro MCX349A-XCCN

Бренд: Mellanox Technologies Страницы: 35

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

Бренд: Connectland Страницы: 10

Бренд: Digisol Страницы: 81

Бренд: Waver Страницы: 36

Бренд: Nexxt Страницы: 2

Бренд: Tenda Страницы: 82

Бренд: AIC Страницы: 79

RouteFinder RF560VPN

Бренд: Multitech Страницы: 82

Бренд: QRS Страницы: 11

Network Expansion Port 2

Бренд: Navico Страницы: 17

Бренд: Infrant Technologies Страницы: 98

Бренд: Dell Страницы: 90

Бренд: D-Link Страницы: 159

Бренд: D-Link Страницы: 169

Бренд: D-Link Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды