background image

 

PM945GZ 

 

Copyright 

All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a 
retrieval system or translated into any language or computer language, in any form or by any means, 
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written 
permission of the company. Brands and product names are trademarks or registered trademarks of their 
respective companies. 
The vendor makes no representations or warranties with respect to the contents herein and especially 
disclaim any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves 
the right to revise this publication and to make changes to the contents herein without obligation to notify 
any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first 
obtaining the vendor’s approval in writing. 

 

Trademark 

All the trademarks or brands in this document are registered by their respective owner. 

 

Disclaimer 

We make no warranty of any kind with regard to the content of this user’s manual. The content is subject 
to change without notice and we will not be responsible for any mistakes found in this user’s manual. All 
the brand and product names are trademarks of their respective companies. 

 

FCC Compliance Statement 

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his own expense. 
However, there is no guarantee that interference will not occur in a particular installation. 

 

CE Mark 

The device is in accordance with 89/336 ECC-ENC Directive. 

 
 
 
 

 

 

 

Ver: EG100

Содержание PM945GZ
































Отзывы: