background image

KM61S-AM2 

 

Copyright 

 

All rights are reserved. No part of this publication may be reproduced, transmitted, transcribed, 

stored in a retrieval system or translated into any language or computer language, in any form 

or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, 

without the prior written permission of the company. Brands and product names are trademarks 
or registered trademarks of their respective companies. 
The vendor makes no representations or warranties with respect to the contents herein and 

especially disclaim any implied warranties of merchantability or fitness for any purpose. Further 
the vendor reserves the right to revise this publication and to make changes to the contents 

herein without obligation to notify any party beforehand. Duplication of this publication, in part or 
in whole, is not allowed without first obtaining the vendor’s approval in writing. 

 
 

Trademark 

 

All the trademarks or brands in this document are registered by their respective owner. 

 
 

Disclaimer 

 

We make no warranty of any kind with regard to the content of this user’s manual. The content 

is subject to change without notice and we will not be responsible for any mistakes found in this 
user’s manual. All the brand and product names are trademarks of their respective companies. 

 
 

FCC Compliance Statement 

 

This equipment has been tested and found to comply with the limits of a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, 

uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. Operation of this 

equipment in a residential area is likely to cause harmful interference in which case the user will 

be required to correct the interference at his own expense. However, there is no guarantee that 

interference will not occur in a particular installation. 

 
 

CE Mark 

 

The device is in accordance with 89/336 ECC-ENC Directive. 

 
 
 
 
 
 
 
 
 
 
 
 

Ver: EG101 

Содержание KM61S-AM2


































Отзывы: