Alamo Great White 8650-A Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 76

background image

MAINTENANCE

Maintenance Section 5-2

© 2005

Alamo Group Inc.

MAINTENANCE

8650A 07/05

Shear Bolts

1. IMPORTANT: If a shear bolt breaks during operation immediately shut down the tractor and replace the
shear bolt.

2. The shear bolts used on these Alamo Industrial snowblower fans are part number 00783578. This shear bolt
is machined around the shank to facilitate shear at the protected fan load.

3. Specified shear bolts and their locations are listed below:

NOTE: Special machined bolt required for fan shear.

IMPORTANT: Tighten nut only enough to draw the shear plates together. Do not over tighten nut.
Occasionally apply grease to the shear plates.

IMPORTANT: Replacement of the shear bolt with one of any other grade or size will be considered
an unauthorized modification and the warranty will be void.

Drive Chain

1. Retighten the auger drive chain when slack exceeds 3/4 inch at the center of the bottom chain section.

2. The drive chain is tightened by loosening the bolts on the idler roller plate and forcing the idler against the chain,
then retightening the bolts.

3. DO NOT OVER TIGHTEN as this will increase wear of the idler roller. Allow approximately 3/8 inch of slack up
or down at the center of the bottom chain section.

Nuts And Bolts

1.Check all nuts and bolts for tightness after the first 5 hours of operation then yearly.

IMPORTANT: Shear bolts should not be over tightened, as this may cause unpredictable shearing action.

«
...
68
69
70
71
72
...
»

Содержание Great White 8650-A













































































Отзывы:

Нет отзывов

Похожие инструкции для Great White 8650-A

Бренд: Tanaka Страницы: 10

POWER X CHANGE PXCBLK-418

Бренд: Ozito Страницы: 6

Pro Sweep 07066

Бренд: Toro Страницы: 103

Бренд: ebm-papst Страницы: 12

Бренд: Poulan Pro Страницы: 52

Бренд: Poulan Pro Страницы: 20

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 12

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 22

Бренд: Black & Decker Страницы: 28

Бренд: Black & Decker Страницы: 2

Бренд: Black & Decker Страницы: 6

Бренд: Black & Decker Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды