Alamo Industrial Axtreme 2 Скачать руководство пользователя страница 110

Страница: 110 / 158

OPERATION

AXTREME 2 02/10

Operation Section 3-24

OPERA

ION

7.2 Lift

The second handle from the left in the bank of five valves actuates the LIFT cylinder. This valve has three
positions.

Pulling the valve handle back, toward the operator, causes the boom LIFT cylinder to lift the boom arm up.

Make certain that you do not lift the head in such a fashion that you lift the left rear wheel off
the ground. Install weight as needed to keep at least 1500 lbs. on the left rear wheel.

If the handle is released, the valve will automatically return to center and boom will be LOCKED in position.

Pushing the handle forward from the locked position will lower the boom.

Again, if the handle is released, the valve will automatically return to center and the boom will be LOCKED in
position.

OPS-B- 0033_C

Never Leave the mower unattended while the head is in the raised
position. The mower could fall causing serious injury to anyone who

might inadvertently be under the mower

(SBM-4)

Содержание Axtreme 2































































































































































Результаты поиска

Содержание Axtreme 2

Отзывы:

Бренды по названию

Популярные бренды

Alamo Industrial Axtreme 2, Руководство оператора

Результаты поиска

Содержание Axtreme 2

Отзывы:

Бренды по названию

Популярные бренды