AL-KO T20-102HDE, Перевод оригинальных инструкций пользователя

Страница: 28 / 38

GB 13
GB
Assembling the grass box
Push the Ø 15 x 26,5 mm sleeve onto the pin and secure
with a quick-clamp.
Place the lower part of the frame on a suitable base (e.g. a
table) and push both the struts (6 mm Ø) into the bores
Œ
.
Position the upper part of the frame, inserting both the struts
into the bores

on the upper part of the frame provided for
this purpose.
Screw the upper part of the frame onto the lower part of the
frame on both sides.
M 6 x 30 hexagonal head screw (2 x)
M 6 x 40 hexagonal head screw (2 x)
Ø 6 x Ø 18 shim (4 x)
M 6 self-locking nut (4 x)
Attention!
Only tighten the nuts by hand to start with due to the
subsequent fixing of the box fabric.
Screw the transverse tube onto the box frame.
M 6 x 45 hexagonal head screw (2 x)
Ø 6 x Ø 12 shim (4 x)
M 6 self-locking nut (2 x)
Place the frame onto the box base of the fabric sack.
Attention!
The ribs of the box base pointing upwards.
Clip the fabric sack onto the box frame.
Remove the upper frame screw connection and screw the
fitting flap of the fabric sack together with the upper and
lower part of the box frame.
Carry out this procedure on both sides.
Screw the box handle
Œ
onto "superstructure left"

and
"superstructure right"
Ž
.
M 8 x 60 screw (2 x)
Ø 8 x Ø 15 shim (2 x)
shim (2 x)
Attention!
The connection contours of the two superstructures
must correspond with the outer contour of the box lid.
Screw the box handle onto the box lid
M 6 x 20 screw (2 x)
Ø 6 x Ø 12 shim (2 x)
Ø 6 x Ø 12 shim (2 x)
M 6 self-locking nut (2 x)
Position the box lid and screw onto the box frame
M 6 x 40 hexagonal head screw (5 x)
Ø 6 x Ø 18 shim (5 x)
Ø 6 x Ø 12 shim (5 x)
M 6 self-locking nut (5 x)
Attention!
Fit the Ø 6 x Ø 18 shim under the screw head.
Push the box strut (Ø 8 mm) through the base of the box
and the lower part of the frame and screw tight.
Ø 8 x Ø 15 shim (2 x)
M 8 self-locking cap nut (2 x)
Assembling the grass box on the tractor
Attention!
To attach the grass box, the rocker of the box locking device
must be parallel to the rear wall of the lawn tractor.
For this, operate the rocker switch of the box lockingdevice.
The arrows on the box lid and the seat console must
match.
Hold the grass box by the box handle in one hand. With the
other hand - gently pressing onto the box lid - position the
upper part of the frame onto the box holding arms and push
forwards until the grass box engages in the bearings.
If the grass box cannot be pushed further forward, lift it up
further.
If the gap between the box lid and the seat console is too
large, the box holding arms can be adjusted by loosening
the screws in the directions shown.
19
21
20
26
27
22
23
24
25
28
29
30
31
41