GB
54
Robolinho 700/1200/2000
Settings
1.
or
* Weekly Program
■
or
* All Days [X]
: The appli-
ance mows every day at the set times. If
All Days [ ]
is shown, the appliance
only mows on the set days of the week.
■
or
* Monday [X]
...
* Sunday
[X]
: The appliance mows for the set
time periods on the set day of the week.
If
Monday [ ]
is shown, for example,
the appliance does not mow on the re-
spective day.
■
or
Change
: Activate the re-
spective day
[X]
or deactivate it
[ ]
,
and set the time periods, type of mowing
and the start points.
2. Make the settings for every day or the re-
spective day:
■
e.g.
*[M] 07:00-10:00 [?]
: Normal
mowing
[M]
from 07:00 – 10:00 am with
automatically changing start point 0 – 9
[?]
.
■
e.g.
*[R] 16:00-18:00 [1]
: The ap-
pliance starts with edge mowing
[R]
at 4
pm and moves along the entire boundary
cable. The area mowing then begins at
start point 1
[1]
. At 6 pm or as soon as
the rechargeable battery is discharged,
the appliance moves back to the base
station.
■
or
Change
: Change the se-
lected setting.
■
or
Continue
: Confirm the
changes setting and continue to the next
setting.
3.
or
Save
: Save all changed set-
tings of the menu item.
7.6
inTOUCH
An existing connection to a gateway can be dis-
connected. This means the appliance is ready to
establish a new connection for 30 minutes.
NOTE
To establish a connection later, the con-
nection must first be disconnected
again, even if the appliance was not pre-
viously connected with a gateway.
1.
or
*inTOUCH
2.
Reset connection
Appliance reports:
Done
.
3. Confirm with
and return to the menu.
7.7
Edge mowing with a manual start
For a manual start, the setting can be made here
that the appliance begins with edge mowing.
Carrying out the edge mowing at the pro-
grammed mowing time periods: see
chapter 7.5.3
"Setting the mowing times", page 53
1.
or
* Margin mowing
2.
or
* at manual start
7.8
Setting the secondary area mowing
1.
or
* Sub zone mowing
2. Setting the mowing time periods:
■
or
inactive
:
Secondary area mowing is switched off.
■
or
active
:
The appliance mows until the recharge-
able battery is flat.
■
or
Mowing time in min
:
The appliance mows the secondary area
for the set time period. The following
mowing time periods can be set:
30/60/90/120/until rechargeable battery
flat.
7.9
Setting the display contrast
If the display is difficult to read, e.g. in sunlight,
the display can be improved by changing the dis-
play contrast.
1.
or
* Display contrast
2. Increase/decrease the display contrast with
or
and accept with
.
7.10 Setting lock
If the setting lock is deactivated, the PIN must on-
ly be entered when acknowledging safety-rele-
vant faults.
1.
or
* Safety settings
2. Activating/deactivating the setting lock:
■
or
Activate
:
Activate the setting lock.
■
or
Deactivate
:
Deactivate the setting lock.
Содержание SOLO Robolinho 1200
