AL-KO 127321, Инструкция по эксплуатации

Страница: 23 / 108

Operation
441582_ F 23
3. Adjusting the motor speed or work speed:
Increasing the work speed: Push the control-
ler (14/3) for the motor speed in the “MAX.
(Hare)” direction.
Decreasing the work speed: Push the con-
troller (14/3) for the motor speed in the “MIN.
(Tortoise)” direction.
4. Rotate the gas lever (14/4) to position “1”.
In position “1” the motor runs at the speed set
on the controller. The motor does not start in
position “0”.
5. Use the grip (14/5) to quickly pull out the star-
ter rope and then let it slowly roll up again.
The motor starts to run.
If the motor does not run: Check that all pre-
vious work steps have been carried out and
then pull the starter rope again.
6. When the motor is running smoothly: Slowly
push the choke lever (14/2) back to the stop.
If the motor starts stuttering, push the choke
lever slightly back in the direction of the choke
symbol.
Stopping the motor:
1. Rotate the gas lever (14/4) to position "0".
2. Close the petrol cock (14/1).
Starting and stopping the tiller blades (13)
Starting the tiller blades:
1. Hold the handlebar by the grip (13/1).
2. Press the safety button (13/2).
3. Press the clutch lever (13/3) on the handlebar
firmly downwards.
After the lever has travelled halfway, the tiller bla-
des begin to rotate and the cultivator starts mo-
ving. After the clutch lever has been pressed fully
downwards, the tiller blades have been comple-
tely started.
Stopping the tiller blades:
1. Release the clutch lever (13/3).
The cultivator stops.
Use the depth skid
When the handlebar of the cultivator – and thus
also the depth skid – is pressed down, the speed
of the cultivator decreases or it stops.
When the handlebar of the cultivator – and thus
also the depth skid – is lifted upwards, the speed
of the cultivator increases.
Engaging/releasing reverse gear, 7505 VR
(15)
1. To stop the tiller blades: Release the clutch
lever (15/3).
2. Pull the lever (15/4) for reverse gear upwards
up to the stop.
3. To start the tiller blades: Press the safety but-
ton (15/2) and firmly press the clutch lever
(15/3) on the handlebar (15/1) downwards.
Operating the gear shift, 7505 V2R (16)
The gear lever (16/1) can be used to switch 2 for-
wards gears and 1 reverse gear. The first forwards
gear is intended for hard ground; the tiller blades
turn slowly. The second forwards gear is intended
for less hard ground; the tiller blades turn faster.
1. To stop the tiller blades: Release the clutch
lever (16/3).
2. Turn the gear lever (16/1) in such a way that it
coincides with the required gear on the plate
(16/2) for the gear display (1 = 1st gear, 2 =
2nd gear, R = reverse gear).
3. To start the tiller blades: Press the safety but-
ton (16/4) and firmly press the clutch lever
(16/3) on the handlebar downwards.
Adjusting the sideways position of the han-
dlebar (17)
Sideways adjustment of the handlebar makes it
possible not to walk on the surface already pro-
cessed. The handlebar can be adjusted by 35° to
either side.
1. Pull the cam lever (17/1) upwards. The
handlebar (17/2) disengages from the holder
(17/3).
2. Turn the handlebar (17/2) to the side (left or
right) up to the stop and keep it in this position.
3. Press the cam lever (17/1) down. The hand-
lebar (17/2) is locked in place.