AL-KO 113842, Перевод оригинальной инструкции по эксплуатации

Страница: 41 / 360

443220_b 41
Operation
7.6 Adjusting the handlebar to your body
size*
* depending on the model, see technical data.
7.6.1 Adjusting the handlebar – easy (14)
1. On both sides of the handlebar:
■
Loosen height adjustment screw (14/1).
■
Pull out screw (14/2).
2. Push upper brace (14/3) to the next hole in
lower brace (14/4) (14/a).
3. Tighten upper brace again in the reverse or-
der.
7.6.2 Adjusting the handlebar – comfort (15,
24)
1. Open quick-release levers (15/1) (15/a).
2. Rotate handlebar (15/2) around rotary/snap-
in joints (15/3) until the desired height is
reached (15/b).
3. Observe marking arrows (24/1).
4. Position plastic washers (24/2) and close the
quick-release levers.
7.6.3 Adjusting the handlebar – premium
(16)
Upper brace
1. Open quick-release levers (16/1).
2. Pull up or push down (16/a) upper brace
(16/2) to the desired height.
3. Close the quick-release levers.
7.7 Folding the handlebar in and out*
* depending on the model, see technical data.
After folding in the handlebar, the appliance can
be placed on its back to allow the mowing mech-
anism to be easily cleaned. This position also
saves space when storing the appliance.
CAUTION! Danger of crushing. Fingers or
other parts of the body can be crushed between
the loose parts of the handlebar.
■
Hold the loose parts of the handlebar tightly.
■
Do not hold any fingers or other parts of the
body between the loose parts.
7.7.1 Folding the handlebar in and out –
comfort (17, 24)
Folding in the handlebar
1. Release upper quick-release lever (17/1) and
fold the upper brace downwards.
2. Release lower quick-release lever (17/2) until
the entire handlebar can be folded forward in-
to the horizontal position.
3. Position plastic washers (24/2) and close all
quick-release levers.
Folding out the handlebar
Proceed in the reverse order.
7.7.2 Folding the handlebar in and out –
premium (18, 25)
Folding in the handlebar
1. Release upper quick-release lever (18/1) and
push in the upper brace up to the stop.
2. Release lower quick-release lever (18/2) until
the lower brace can be folded forward into
the horizontal position.
3. Position plastic washers (25/2) and close all
quick-release levers.
Folding out the handlebar
Proceed in the reverse order.
7.8 Starting and stopping the mower
mechanism (19, 20)*
* depending on the model, see technical data.
Start the mower mechanism on level ground and
not in long grass. The ground must be free of for-
eign bodies such as stones. Do not lift or tilt the
appliance to start it.
Starting the mower mechanism
1. If you have not already done so: Switch on
the power supply (see chapter 6.3 "Switching
the power supply on and off (06)", page 39 ).
2. Press start button (19/1, 20/1) and hold.
3. Pull operator presence control (19/2, 20/2) to-
wards the handlebar (19/3, 20/3) (19/a, 20/a).
The motor and mower mechanism are start-
ed.
4. Release the start button and keep holding the
operator presence control.
NOTE The operator presence control does
not lock in place. Hold it tight against the handle-
bar during the entire working period.
Stopping the mower mechanism
1. Release the operator presence control. It au-
tomatically returns to its starting position.
2. Wait for the mower mechanism to come to a
standstill.