MECHANICAL CHARACTERISTICS
Enclosure
Self-extinguishing plastic material class V0
Protection degree
IP40 on front panel
Dimensions
70 x 90 x 58 mm (4 DIN modules)
VOLTAGE INPUT
Direct
Fino a 300 V
max 360 V
Power supply
18-60VDC
Self consumption
< 3VA
MODELS
PFA7471-08
ATTO D4 DC RS485 18-60VDC
ENERGY ANALYSER
PFA7471-18
ATTO D4 DC RS485 18-60VDC 1DI 2DO
ENERGY ANALYSER
!
ATTO D4 DC
The instrument is programmed with the following default values:
PAGE
MENU DISPLAYED
AVAILABLE PARAMETERS
DEFAULT
PASSWORD REQUESTED
0000 ... 9999
0000
RS485
RS 485 ADDRESS
1 ... 247
27
Comm. Speed
2400, 4800, 9600, 19200, 38400
38400
Data Bit
7 o 8
8
Parity
N = no parity, E = peer parity, O = odd parity
N
Bit of stop
1 o 2
2
NETWORK
Export
NO, YES
NO
I FS
1 ... 10000
00010
SHUNT
60 o 100
60
VR
400000/999
1/1
AVG-MD TIME (note n.2)
POWERS
1...60 (minutes)
15
CURRENTS
1...60 (minutes)
8
ALARM 1 / A
(
note n.11)
MODE (
note n.3)
Normal, DERIV
NORMAL
TYPE (
note n.4)
MAX, MIN
MIN
MEAS (
note n.5)
Controlled measure. See table n.1 for register
selection.
200
THRE (
note n.5)
Valore soglia
0
ALARM 1 / B
HYST
1...100 (%)
1
DELAY
1...99 (seconds)
1
AVG (
note n.6)
1...99 (seconds)
1
OUT (
note n.7)
Normal, Hold, Pulse-L, Pulse-S
NORMAL
ALARM 2 / A
(
note n.11)
MODE (
note n.3)
Normal, DERIV
NORMAL
TYPE (
note n.4)
MAX, MIN
MIN
MEAS (
note n.5)
Controlled measure. See table n.1 for register
selection.
200
THRE (
note n.5)
Valore soglia
0
ALARM 2 / B
HYST
1...100 (%)
1
DELAY
1...99 (seconds)
1
AVG (
note n.6)
1...99 (seconds)
1
OUT (
note n.7)
Normal, Hold, Pulse-L, Pulse-S
NORMAL
ALARM 3 / A
(
note n.11)
MODE (
note n.3)
Normal, DERIV
NORMAL
TYPE (
note n.4)
MAX, MIN
MIN
MEAS (
note n.5)
Controlled measure. See table n.1 for register
selection.
200
THRE (
note n.5)
Valore soglia
0
ALARM 3 / B
HYST
1...100 (%)
1
DELAY
1...99 (seconds)
1
AVG (
note n.6)
1...99 (seconds)
1
OUT (
note n.7)
Normal, Hold, Pulse-L, Pulse-S
NORMAL
ALARM 4 / A
(
note n.11)
MODE (
note n.3)
Normal, DERIV
NORMAL
TYPE (
note n.4)
MAX, MIN
MIN
MEAS (
note n.5)
Controlled measure. See table n.1 for register
selection.
200
THRE (
note n.5)
Valore soglia
0
ALARM 4 / B
HYST
1...100 (%)
1
DELAY
1...99 (seconds)
1
AVG (
note n.6)
1...99 (seconds)
1
OUT (
note n.7)
Normal, Hold, Pulse-L, Pulse-S
NORMAL
DIGITAL OUT 1
(
note n.8)
MODE
PULSE, ALARM, REMOTE
PULSE
POLARITY
NO, NC
NO
PULSE OUT 1
MEAS (
note n.9)
P-IMP, P-EXP
P-IMP
PRIMARY (
note n.10)
YES, NO
YES
WEIGHT
1...100000000 (Wh/100)
100000
WIDTH
50ms...1S
500
DIGITAL OUT 2
(
note n.8)
MODE
PULSE, ALARM, REMOTE
PULSE
POLARITY
NO, NC
NO
PULSE OUT 2
MEAS (
note n.9)
P-IMP, P-EXP
P-EXP
PRIMARY (
note n.10)
YES, NO
YES
WEIGHT
1...100000000 (Wh/100)
100000
WIDTH
50ms...1S
500
Subject to modifi cation without notice. Edition 11-02-2011.
COPYRIGHT
Electrex is a trademark of Akse S.r.l. All rights reserved.
It is forbidden to duplicate, adapt, transcript this document without Akse written
authorization, except when regulated accordingly by the Copyright Laws.
WARRANTY
This product is covered by a warranty against material and manufacturing defects for a
period of 24 months period from the manufacturing date.
The warranty does not cover the defects that are due to:
• Negligent and improper use
• Failures caused by atmospheric hazards
• Acts of vandalism
• Wear out of materials
• Firmware upgrades
Akse reserves the right, at its discretion, to repair or substitute the faulty products
The warranty is not applicable to the products that will result defective in consequence of
a negligent and improper use or an operating procedure not contemplated in this manual.
RETURN AND REPAIR FORMALITIES
Akse accepts the return of instruments for repair only when authorized in advance. The
transport costs are at customer charge.
RE-SHIPPING OF REPAIRED PRODUCT
The terms for re-shipment of repaired products are ex-works, i.e. the transport costs are
at customer charge.
Products returned as detective but found to be perfectly working by our laboratories, will
be charged a fl at fee to account for checking and testing time irrespective of the warranty
terms.
SAFETY
This instrument was manufactured and tested in compliance with IEC 61010 CAT III-300V,
class 2 standards for operating voltages up to 300 VAC rms phase to neutral.
In order to maintain this condition and to ensure safe operation, the user must comply with
the indications and markings contained in the following instructions:
• When the instrument is received, before starting its installation, check that it is
intact and no damage occurred during transport.
• Before mounting, ensure that the instrument operating voltages and the mains
voltage are compatible then proceed with the installation.
• The instrument power supply needs no earth connection.
• The instrument is not equipped with a power supply fuse; a suitable external
protection fuse must be foreseen by the contractor.
• Maintenance and/or repair must be carried out only by qualifi ed, authorized
personnel
• If there is ever the suspicion that safe operation is no longer possible, the instrument
must be taken out of service and precautions taken againstits accidental use.
• Operation is no longer safe when:
1) There is clearly visible damage.
2) The instrument no longer functions.
3) After lengthy storage in unfavorable conditions.
4) After serious damage occurred during transport
The instruments must be installed in respect of all the local regulations.
OPERATOR SAFETY
Warning:
Failure to observe the following instructions may lead to a serious danger of
death.
• During normal operation dangerous voltages can occur on instrument terminals and
on voltage and current transformers. Energized voltage and current transformers
may generate lethal voltages. Follow carefully the standard safety precautions while
carrying out any installation or service operation.
• The terminals of the instrument must not be accessible by the user after the installation.
The user should only be allowed to access the instrument front panel where the
display is located.
• Do not use the digital outputs for protection functions nor for power limitation functions.
The instrument is suitable only for secondary protection functions.
• The instrument must be protected by a breaking device capable of interrupting both
the power supply and the measurement terminals. It must be easily reachable by the
operator and well identifi ed as instrument cut-off device.
• The instrument and its connections must be carefully protected against short-circuit.
Precautions:
Failure to respect the following instructions may irreversibly damage to the
instrument.
• The instrument is equipped with PTC current limiting device but a suitable external
protection fuse should be foreseen by the contractor.
• The outputs and the options operate at low voltage level; they cannot be powered by
any unspecifi ed external voltage.
• The application of currents not compatible with the current inputs levels will damage
to the instrument.
Further documentation may be downloaded from our web site www.electrex.it.
This document is owned by company AKSE that reserves all rights.
DECLARATION OF CONFORMITY
Akse hereby declares that its range of products complies with the following directives EMC
89/336/EEC 73/23CE 93/68 CE and complies with the following product’s standard
CEI EN 61326 – IEC 61326 CEI EN 61010 – IEC 1010.
The product has been tested in the typical wiring confi guration and with peripherals
conforming to the EMC directive and the LV directive.
INSTALLATION INSTRUCTIONS
