Akai RPM500 Скачать руководство пользователя страница 5

 

 5 

 

 

 

Setup 

 
The configuration and placement of your RPM500 monitors on speaker stands or your desktop 
workstation may affect the performance of the speakers. Use the following tips to achieve the 
best performance out of your RPM500 monitors. 

Tip:

 If possible, place your RPM monitors on speaker stands instead of your desk top. Desks 

tend to resonate sympathetically at low frequencies and may adversely affect the bass 
response of your monitors. If speaker stands are not possible due to space restrictions and you 
notice a buildup in bass, try placing the monitors on isolation pads (included) to acoustically de-
couple the monitors from the desk. 

 

Speaker Placement 

 
Place the RPM500 monitors so that the two speakers 
and the engineer form an equilateral triangle when 
viewed from above. Angle the speakers slightly inward 
so that the drivers face the engineer. 

In general, it is recommended that RPM500 monitors 
be placed at least one foot away from the nearest 
wall, ceiling, or any other large, flat surface (the 
reason for this is covered in detail in the following 
chapter of this guide). If practical considerations such 
as limited studio space make this impossible, 
RPM500 monitors include separate equalizer controls 
to compensate for placement near walls and corners, 
as well as to compensate for the general acoustic 
response of your monitoring environment. 
 

Speaker Height 

 
Position the speakers so that they are parallel to the 
ground and that your ears are between the midpoint of 
the woofer and the tweeter. 
 
 
 
 
 
 

Speaker Orientation 

 
If possible, place the RPM500 monitors in their upright position and avoid laying the speakers 
on their sides. The RPM500 woofer and tweeter are vertically aligned and will provide the best 
performance when the speakers are placed upright. Placing them on their sides may create 
strong reflections from nearby surfaces resulting in spectrally unbalanced sound. 

If your RPM500 monitors must be oriented horizontally due to space or line-of-sight 
considerations, place the speakers so that their tweeter is on the "inside" to improve imaging. 
 

              

 

Tweeters

Содержание RPM500









Отзывы: