AJA Io IP Скачать руководство пользователя страница 44

Страница: 44 / 86

Io IP Transport, Capture, Display v16.2r1 44 www.aja.com

Match Checkboxes

The ‘Match’ checkbox can be used to match the Destination Port to the

Destination IP Address.

Playout Delay

The Playout Delay slider can be used to adjust the amount of buffering before

packets are sent to the network, in a range of 0 to 150 milliseconds. Network

traffic conditions may require setting a larger buffer. Default is 50 milliseconds.

IP Input Screen, 2022-7 Operation

These fields will only be available when 2022-7 is Enabled in the IP Network

section. See

"IP Network Screen, 2022-7 Operation" on page 42

Destination IP Addr 2

This filter lets you specify the network address where a duplicate multicast from

another 2022-7 device on the network can be found. That device should be

sending two duplicate IP video multicasts and the IP addresses of those streams

will be specified in ‘Destination IP Addr’ and ‘Destination IP Addr 2’.

Destination Port 2

This filter lets you specify the port number being used to send a multicast to the

‘Destination IP Addr 2’ address specified above.

Path Difference

The Path Difference slider can be used to adjust the buffering used for redundant

operation, where the paths through the network of the two streams may

have different delays. Adjustable in a range of 0 to 150 milliseconds, with 50

milliseconds the default.

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды