AJA Io IP Скачать руководство пользователя страница 19

Страница: 19 / 86

Io IP Transport, Capture, Display v16.2r1 19 www.aja.com

Chapter 3 – Io IP Operation

Using Io IP with Professional Video /Audio Software

After you install the AJA software package on your computer, you’re ready to

begin capturing and playing back video and audio using your choice of third-

party software. You can go here for AJA software and documentation:

https://www.aja.com/en/support/downloads

For further support information and downloads for third-party software, go to:

https://www.aja.com/compatibility/io

Frequently Asked Question documents for various AJA products are available at:

https://www.aja.com/products/kona-ip#support

Capture Formats

When capturing, you can record data in the following file formats:

•  DPX
•  TGA
•  BMP
•  QuickTime
•  MX
•  MP4

NOTE: Support by Io IP of QuickTime for Windows has been discontinued. Instead, AJA

supports ProRes family capture and playback for macOS and Windows via AJA

Control Room.

NOTE: Other file types can be captured using third-party capture applications such as

Sienna, Softron, Tools on Air, Drastic Technologies, or Quadrus.

AJA Control Panel Overview

The AJA Control Panel is a software application that provides a simple visual

showing how the Io IP hardware is currently configured and allows you to make

changes. You can change signal input and output parameters and define the

video processing that will be performed.
The AJA software installer automatically installs the Control Panel application on

your computer.

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды