AJA FS2 Скачать руководство пользователя

Страница: 17 / 125

FS2 v2.1r1

www.aja.com

• Hold down a button (turns blue) to make coarse adjustments using the

Adjust

knob.

Release the button to make fine adjustments.

The following text briefly lists the functions accessed by each pushbutton:

STATUS

Displays the Status Menu Group, which shows current machine status and error
conditions:

• Video 1, Video 2, and Caption status

• Reference and Genlock status

• Output Status

• Power and Temperature status

• System Name display

• Alarms

REMOTE

Displays the Remote Menu Group, which lets you select how to control the FS2:

• Control by local front panel, remote devices, or local and remote

• GPI input and output behavior

CONFIG

Displays the Config Menu Group, which lets you configure the FS2 for your environment:

• System Name setting

• IP and SNMP settings, MAC address

• Alarm control

• Hidden Menus and Display intensity (brightness)

• System serial number and software version

• System reboot

PRESET

Displays the Reg Menu Group, which accesses the memory registers:

• Store, Recall, and edit the names of Presets

• Factory Preset (defaults)

SYSTEM

Displays the System Menu Group, which lets you change or enable FS2 video and audio
input and system functions:

• Video input format settings, including 3G setup

• Audio input format and sample rate conversion settings

• Genlock reference source selection

• Frame rate selection and NTSC standard (North America/Japan)

• Input downconversion setting (HD to SD)

• HDMI RGB Range

OUTPUT

Displays the Output Menu Group, which selects output sources:

• Composite downconversion

• Video output selections

• Audio output selections

• 3 G output configuration

• HDMI video and audio configuration

VIDEO 1 and 2

Displays the Menu Groups that access Video Processor video input, format, and
conversion selections and adjustments (separate buttons access Video Processor 1 and
Video Processor 2):

USO

RESTRITO

Содержание FS2






























































































































Результаты поиска

Содержание FS2

Отзывы:

Похожие инструкции для FS2

Бренды по названию

Популярные бренды

AJA FS2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FS2

Отзывы:

Похожие инструкции для FS2

Бренды по названию

Популярные бренды