AJA FS-HDR Скачать руководство пользователя страница 82

Страница: 82 / 129

FS-HDR Frame Synchronizer/Converter/HDR-WCG Processor v1.0r1 82 www.aja.com

Figure 31. SD Aspect Ratio Conversion Illustrations

SD Aspect Ratio Conversion Illustrations

H Crop

Pillarbox

V Crop

14:9

Off

(no conversion)

Letterbox

4:3 Converts To

These displays on 4:3

7 Upconvert Mode

These parameters select the type of upconversion the Video Processor performs

on the selected input. This parameter has an effect only when the input has a

narrower aspect ratio than the output (SD > HD, HD > 2K). When converting from

2K, the selections do not precisely describe the resulting picture. For example,

4x3 pillar is not precisely 4x3, and 14x9 is not precisely 14x9. However, picture

scaling is such that the visual effect closely resembles an SD-to-HD upconvert.

4x3 Pillar (default)

14x9 Pillar

Full Screen

LB to Full

Wide Zoom

Results in 4x3 image at center screen with black sidebars.

Results in 14x9 image, zoomed slightly to fill a 14x9 image with

sidebars.

Anamorphic full screen display.

Image is zoomed to fit the full screen (letterbox).

Using a combination of zoom and stretch, the image is sized to fit a

16x9 screen (this can introduce a small aspect ratio change).

NOTE: Any Custom Size/Pos values (only available in Four Channel Mode) will be applied

on top of this settings.

Содержание FS-HDR


































































































































Результаты поиска

Содержание FS-HDR

Отзывы:

Похожие инструкции для FS-HDR

Бренды по названию

Популярные бренды

AJA FS-HDR, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FS-HDR

Отзывы:

Похожие инструкции для FS-HDR

Бренды по названию

Популярные бренды