AJ SSLFHFD-FP Скачать руководство пользователя страница 5

Страница: 5 / 29

Line voltage

wiring knockouts

Main power switch

Installation

The terminal unit is fully assembled from the factory with the exception

of the HEPA filter and lamps (as applicable) which is shipped in a separate box.

Step 1 -- Carefully remove the unit from the shipping carton and inspect for

damage that may have occurred during shipping. If shipping damage is found,

do not install. Call the manufacturer to report damage.

Step 2 -- Wipe down unit to remove shipping dust and debris.

Step 3 -- Raise unit into ceiling and lower onto gasketed opening.

Gasket should be a closed-cell material approved for the environmental

conditions. It is highly recommended to further support the unit from

above using the tabs welded to the plenum.

Step 4 -- A qualified technician should connect the unit to the appropriate

power supply per applicable codes and standards. Refer to the wiring

diagrams included in these instructions. -FP and -MA units: the electrical

box will be accessible from the plenum side. -MEA units: the electrical

box will be accessible from the roomside.

NOTE

: If an -MA or -MEA unit is installed in an area with no access above the

ceiling, the main power switch

must

be turned on before installing unit

NOTE:

An additional disconnect should be added by others per local codes

and regulations.

SSLFHFD-FP-120 --- 120VAC SUPPLY

SSLFHFD-FP-208/240 --- Duel rated 208 or 240VAC SUPPLY

SSLFHFD-FP-277 --- 277VAC SUPPLY

Step 5 -- Blow out / clean entire duct system leading to unit to remove construction

debris. This is especially important for motor accessible units as they do not have a

pre-filter. Wash pre-filter if applicable per “Cleaning the Fan Filter Unit Pre-filter” on page 7.

Step 6 -- Install the HEPA filter per the “Removal and Replacement of the HEPA Filter

with Gel Seal” section.

NOTE: FOR DUCTED INSTALLATIONS, IT IS RECOMMENDED

THAT PRIMARY AIR BALANCING TO ACHIEVE 0.0"WC INLET

STATIC PRESSURE BE DONE BEFORE FAN FILTER UNIT IS

CONNECTED TO DUCT SYSTEM.

DRAWING NAME

DRAWN

Содержание SSLFHFD-FP






























Результаты поиска

Содержание SSLFHFD-FP

Отзывы:

AJ SSLFHFD-FP, Инструкция по эксплуатации, Страница: 5 / 29

Результаты поиска

Содержание SSLFHFD-FP

Отзывы: