AJ Aircraft Acuity Скачать руководство пользователя | Manualshive

Страница: 4 / 24

background image

aj-aircraft.com

Page 3

Optional Configurations

You have the option of using a pull-pull rudder servo or a push-pull rudder servo setup. Fasteners, control horns and
servo connecting rods are provided for optional rudder setups.

Recommended Items for Completion



Hacker A50-12s



Falcon 16x10 prop



Castle 90 ESC



Thunder Power 5s 5000mah LiPo



Futaba BLS1053/BLS551 Servos on Elevator/Rudder



Futaba S9670SV Servos on Ailerons



(4) x 6" Servo Extensions for the Ailerons and Rx to Wing



(1) x 12" Servo Extension for the ESC to Receiver



(1) x 36" Servo Extension for the Elevator



(6) Servo Connector Safety Clips



2.75" or 70mm Spinner

Tools Needed

Blue Painter’s Masking Tape
Thin CA Glue
30 Minute Epoxy
Denatured Alcohol
Paper Towels
Removable Thread Locker (Loctite 242, Blue)
Metric & Imperial Allen Wrenches
Hobby Knife & Fresh Blades
Covering Iron (Trim Iron)

Clamps
Small Flat File
Electric Drill w/ Assorted Small Bits (1/16”, 5/64”)
Small Flat Blade Screwdrivers
Small Phillips Screwdriver
Sandpaper (150-220 Grit)
Pliers
Measuring Tape & Ruler

«
...
2
3
4
5
6
...
»

Содержание Acuity

























Отзывы:

Нет отзывов

Похожие инструкции для Acuity

Бренд: Bachmann Страницы: 12

FORKLIFT PB 1420B

Бренд: Laser Pegs Страницы: 20

9025 Fire Dragon

Бренд: Laser Pegs Страницы: 4

Бренд: Spin Master Страницы: 4

G2579 The Incredibles

Бренд: Fisher-Price Страницы: 10

Бренд: Kyosho Страницы: 15

PICHLER Beechcraft T-34C TURBO MENTOR

Бренд: VQ Radio Control Model Страницы: 12

Бренд: Jamara Страницы: 8

Бренд: HobbyBoss Страницы: 16

Voice Activated Uni

Бренд: Neopets Страницы: 2

Бренд: C&C Models Страницы: 23

Бренд: Fisher-Price Страницы: 28

Бренд: TILLIG BAHN Страницы: 3

Goblin 570 Sport

Бренд: SAB Heli Division Страницы: 36

Бренд: Kibri Страницы: 3

FLYBARLESS Sole V3 FBL 2,4 GHz

Бренд: Jamara Страницы: 8

Fw 200 Condor exterior

Бренд: Eduard Страницы: 2

Бренд: Eduard Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды