AJ Aircraft Acuity Скачать руководство пользователя | Manualshive

Страница: 12 / 24

background image

aj-aircraft.com

Page 11

Fuselage

Inspect the fuselage for any interior joints that may have
loosened as a result of shipping & handling. Apply thin
CA glue as needed. Apply thin CA glue around the joints
of the fuselage core, firewall, fuselage formers, and
rudder servo tray to strengthen.

Carefully locate the horizontal stabilizer pocket. Use an
iron to seal the covering around the edges of the pocket
before trimming. Use a new hobby knife blade to cut
though the covering.

Review the servo configurations as described on page 3
before cutting the covering over the servo pockets.
There are 2 servo pockets below the horizontal stabilizer
slot on both sides of the fuselage (highlighted with tape).
The front pocket will be used for the elevator servo. The
pocket near the tail of the fuselage on the opposite side
will be for a rudder servo if you decide to use the push-
pull configuration.

«
...
10
11
12
13
14
...
»

Содержание Acuity

























Отзывы:

Нет отзывов

Похожие инструкции для Acuity

Бренд: Bachmann Страницы: 12

Бренд: BARCLONE Страницы: 14

Бренд: K'Nex Страницы: 30

Бренд: K'Nex Страницы: 44

40 MODEL BUILDING SET

Бренд: K'Nex Страницы: 13

Бренд: K'Nex Education Страницы: 35

Бренд: K'Nex Страницы: 2

Бренд: K'Nex Education Страницы: 24

100 MODEL IMAGINE BUILDING SET

Бренд: K'Nex Страницы: 78

100 MODEL IMAGINE BUILDING SET

Бренд: K'Nex Страницы: 64

Бренд: RC4WD Страницы: 79

SQUADRON'S STEARMAN

Бренд: RED BARON PIZZA Страницы: 39

THE GHOST HOUSE

Бренд: RavensBlight Страницы: 10

B-17G radio compartment

Бренд: Eduard Страницы: 4

Бренд: MTHTrains Страницы: 36

Бренд: Faller Страницы: 8

Alexander Schleicher ASK 13

Бренд: Paolo Severin Страницы: 28

Aces Wild Custom Chopper

Бренд: REVELL Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды