62
61
1. How to Start Up the MD Test Mode
While pressing the MD function key, insert the AC plug to the power outlet.
Note:
1) The CX-NH560 can start up the test mode ignoring the mechanism abnormality even if any abnormality is occurring. If
the abnormality occurs, disconnect the AC plug quickly.
2) Normal playback/recording cannot be performed while the test mode is in progress.
2. Checking the MD Test Mode
Indication on display
About five seconds later after the test mode has started up, the following message appears and the test mode becomes ready to be
operated.
3. How to Exit the MD Test Mode
1)
Press the “MD EJECT” key and remove the disc.
2)
Disconnect the AC plug.
*
If the machine exits the MD test mode by any methods other than the procedure as described above, the machine may operate
abnormally when the POWER is turned on next time. In such a case, disconnect the AC plug.
4. How to Switch to Servo Standby Mode
When the test mode has been established, the mode is switched to the servo standby mode by pressing the STOP key. (“ALL SVoFF”
is displayed.) Switch this mode to each mode.
Returns to “ALL SVoFF” by pressing the STOP key from each operation.
5. Checking the Sled Operation
1)
2)
1)
The laser power output level can be switched by every pressing of the EDIT key in the “ALL SVoFF”. The indication is switched
as shown below.
2)
After confirming the message, press the STOP key to display the “ALL SVoFF”.
TEST MODE < MD >
7. Checking the Operation of Loading Mechanism/OWH
The operations of the loading mechanism and the OWH are checked by the procedure below.
Method 1: Insert a MO disc to the desired slot among the magazines 1 to 3, and press the MD direct play key of the slot. After
loading, confirm that the EON and the AG on the display lights off and the OWH moves up.
Method 2: Loading is started by pressing the 1CD
™
1MD key in the “ALL SVoFF”. The loading can be performed without a
disc. When a disc is loaded, insert the disc into the slot that the elevator stops at. The OWH moves down by pressing
the 1CD
™
1MD key in the loading status, and the OWH moves up by pressing the MD EJECT key.
1CD
™
1MD key..........Loading/OWH DOWN
MD EJECT key..........Unloading/OWH UP
*
The status of the loading mechanism and OWH can be checked by FL indication.
*
The AG indicates the loading SW. The EON and REC SW indicate the status of the REC SW.
Note:
The loading cannot be performed by the MD direct play key without a disc (The disc switch is off.). (The loading can be
performed by 1CD
™
1MD key.)
8. Checking the Indication and Turning On/Off of Each Switch
The status of each switch can be confirmed by the indication on the display.
Note:
The SW ON indicates the status when the switch is pressed.
The loading status is shown by the combination of the AG and EON.
The elevator status is shown by the combination of the RT and TRAF.
Status of each indication
Status of loading mechanism and OWH
EON is displayed only
Loading/OWH DOWN
Both AG and EON lights off
Loading/OWH UP
Both AG and EON lights on
Unloading/OWH UP
Indication on the display
T-BASS
AUTO MARK
TIME MARD
ROCK
POP
CLASSIC
AG
EON
RT
TRAF
Function name
Laser power
Disc mode
Disc mode
Write-protection detection SW
Reflectance detection SW
INSIDE LIMIT SW
LOADING SW
REC SW
Elevator SW (S701)
Elevator SW (S702)
Light on
Indicated by the level meter of the three steps
(READ-1/2-WRITE)
MO DISC (GROOVE)
PIT DISC (PIT)
REC protection
High reflectance (PIT DISC)
SW ON (innermost track)
SW OFF
SW OFF
SW OFF
SW OFF
1
2
3
4
5
6
7
8
9
0
Light off
REC OK
Low reflectance (MO DISC)
SW OFF
SW ON
SW ON
SW ON
SW ON
w w w . x i a o y u 1 6 3 . c o m
Q Q 3 7 6 3 1 5 1 5 0
9
9
2
8
9
4
2
9
8
T E L
1 3 9 4 2 2 9 6 5 1 3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
