manualshive.com logo in svg

Aiwa TV-CN202, Руководство по обслуживанию, Страница: 3 / 33

Поделиться
Скачать
Aiwa TV-CN202 Скачать руководство пользователя страница 3

3

NOTICES  BEFORE  REPAIRING

To make the best use of this equipment, make sure to
obey the following items when repairing (or mending).

1. Do not damage or melt the tunicate of the leading

wire on the AC1 side, including the power supply
cord.

2. Do not soil or stain the letters on the spec.

inscription plates, notice labels, fuse labels, etc.

3. When repairing the part extracted from the

conducted side of the board pattern, fix it firmly
with applying bond to the pattern and the part.

4. Restore the following items after repairing.
1) Conditions of soldering of the wires (especially,

the distance on the AC1 side).

2) Conditions of wiring, bundling of wires, etc.
3) Types of the wries.
4) Attachment conditions of all types of the insulation.
5. After repairing, always measure the insulation

resistance and perform the voltage-withstand test
(See Fig-1).

1) The insulation resistance must be 7.0 to 9.5 M

Ω

when applying 

500V 

per second.

2) In the voltage withstand test, apply 3.6 KV for 3

seconds and check that the GO lamp lights.

the designated parts must be used.

4. Put parts and wires in the original position after

assembling or wiring.
There are parts which use the insulation material
such as a tube or tape for safety, or which are
assembled so that these parts do not contact with
the printed board. The inside wiring is designed not

to get closer to the pyrogenic parts and high voltage
parts. Therefore, put these parts in the  original
positions.

5. Take care ofts incode-rays a t.ter

Howevaft53 -3.5when removwirint5(, clovwirifromnal)]TJ0001 [(backw bo,int5ng iangerousser givher shockrts.5.6740(T)104.3(ter)]TJ6.3833 -1.2 T*-0.000c T*-0.0001 Tenou hike caer deginct wintons.)T3.16733 -1.2 TD0.0001 Tw6[(5.)-.1(A)13.67voidian X-ray
Tgincircuit,fetcrts7.6749(Thereforwhen repae wiriut nal)]TJ0-0.0001 Tnd high volt s wp9(Tgincircuit,fch use the designang.)TjT*-0.0001 Tic parts ats do nohangeput   ircuit. Repae wirng.
except5nndi inwircach s rismblinf nd high volt,rts ng.

7[(4.)-74ereremer sr saficheckion af clovwcwiriner

Содержание TV-CN202


































Отзывы:

Нет отзывов