background image

INSTALLATION DETAILS

                                                                                                       

 

 

HKD DCI                                                                      35                                                                Version - 2 

6).  Disconnect  the  charge  set  and  the  charging 

cylinder,  and  set  the  2-way  and  3-way  valves  to 

the open position 

Be sure to use a hexagonal wrench to operate the 

valve stems. 

7).  Mount  the  valve  stems  nuts  and  the  service 

port cap 

Be  sure  to  use  a  torque  wrench  to  tighten  the 

service port cap to a torque 18N.m. 

Be sure to check the gas leakage. 

8.7  Re-installation while the outdoor unit 

need to be repaired 

8.7.1 

Evacuation for the whole system 

 

Procedure: 

1).

 

Confirm  that  both  the  2-way  and  3-way 

valves are set to the opened position.

 

2).  Connect  the  vacuum  pump  to  3-way  valve

’s 

service port. 

3).  Evacuation  for  approximately  one  hour. 

Confirm  that  the  compound  meter  indicates 

-0.1Mpa. 

4). Close the valve (Low side) on the charge set, 

turn  off  the  vacuum  pump,  and  confirm  that  the 

gauge  needle  does  not  move  (approximately  5 

minutes after turning off the vacuum pump). 

5). Disconnect the charge hose from the vacuum 

pump. 

 

8.7.2 

Refrigerant charging 

 

Procedure: 

1).  Connect  the  charge  hose  to  the  charging 

cylinder,  open  the  2-way  valve  and  the  3-way 

valve 

Connect 

the 

charge 

hose 

which 

you 

disconnected  from  the  vacuum  pump  to  the 

valve  at  the  bottom  of  the  cylinder.  If  the 

refrigerant is R410A, make the cylinder bottom 

up to ensure liquid charge. 

2). Purge the air from the charge hose 

Open  the  valve  at  the  bottom  of  the  cylinder 

and press the check valve on the charge set to 

purge  the  air  (be  careful  of  the  liquid 

refrigerant). 

3) Put the charging cylinder onto the electronic 

scale and record the weight. 

4). Open the valves (Low side) on the charge set 

and charge the system with liquid refrigerant 

If the system cannot be charge with the specified 

amount  of  refrigerant,  or  can  be  charged  with  a 

little  at  a  time  (approximately  150g  each  time)  , 

operating the air conditioner in the cooling cycle; 

however,  one  time  is  not  sufficient,  wait 

approximately  1  minute  and  then  repeat  the 

procedure. 

5).When  the  electronic  scale  displays  the  proper 

weight,  disconnect  the  charge  hose  from  the 

3-

way valve’s service port immediately 

If  the  system  has  been  charged  with  liquid 

refrigerant  while  operating  the  air  conditioner, 

turn off the air conditioner before disconnecting 

the hose. 

6). Mounted the valve stem caps and the service 

port 

Содержание AWAU-YKD009-H11

















































































Отзывы: