En-3
TIMER OPERATION (ON timer/OFF timer/PROGRAM timer/SLEEP timer)
Instructions relating to heating are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
The timer functions cannot be used when this controller is used together with the Remote Controller (Wired type).
A beeping sound is made when a signal is received.
To set the ON/OFF timer
1
2
To set the PROGRAM timer
Adjust the OFF or ON time.
(About 5 seconds later, the
entire display will reappear.)
Select “OFF TIMER” or “ON TIMER”.
1
2
3
4
5
Select “OFF TIMER”.
Adjust the OFF
time.
Select “ON TIMER”.
Adjust the ON time.
(About 5 seconds later, the entire display
will reappear.)
Select “PROGRAM TIMER”.
(Either OFF
→
ON or OFF
←
ON
will display.)
(If the ON
timer has been se-
lected to operate first, the unit
will stop operating at this point.)
Select “TIMER RESET”.
The air conditioner will return to normal op-
eration.
To cancel the TIMER
To change operating conditions
If you wish to change the operating conditions (ON/OFF, Mode,
Fan Speed, Temperature Setting), after making the time set-
ting, wait until the entire display reappears, then press the ap-
propriate buttons to change to the desired operating condition.
OPERATION
Instructions relating to heating are applicable only to “HEAT & COOL MODEL” (Reverse Cycle).
To start/stop operation
Start time: The indoor unit’s operation indicator lamp (red) will light up.
Stop time: The indoor unit’s operation indicator lamp (red) will go out.
Operation mode setting
Room temperature setting
Fan speed setting
→
→
COOL
→
DRY
HEAT
←
FAN
←
→
→
HIGH
→
MED
→
LOW
Vertical air direction adjustment (Swing operation)
Horizontal air direction adjustment (Swing operation)
Press the START/STOP button to start the air conditioner, and then proceed as follows.
NOTES
To set the operation mode
To set the swing operation, press the VERTI-
CAL SWING button (Stop the setting by press-
ing it once again.)
To set the swing operation, press the HORIZON-
TAL SWING button (Stop the setting by press-
ing it once again.)
(1)
• Always use the remote controller’s AIRFLOW DIRECTION button.
Attempting to move the air direction louvers manually could re-
sult in improper operation; in this case, stop operation and re-
start.
The flaps should begin to operate properly again.
• During use of the Cooling mode, do not set the VERTICAL air
direction flap in the
4
position for long time, since water vapor
may condense near the outlet port and drops of water may drip
from the air conditioner.
(2)
• The range of swing is relative to the currently set airflow direc-
tion.
• The SWING operation may stop temporarily when the air condi-
tioner’s fan is not operating, or when operating at very low speeds.
<Vertical airflow swing operation>
Airflow direction
Range of swing
1
1
to
3
2
2
to
4
3
2
to
4
4
1
to
4
(All range)
<Horizontal airflow swing operation>
Airflow direction
Range of swing
1
1
to
5
(All range)
2
1
to
3
3
2
to
4
4
3
to
5
5
1
to
5
(All range)
Temperature setting range:
AUTO ............... 18 to 30
°
C
Heating ............ 16 to 30
°
C
Cooling/Dry ..... 18 to 30
°
C
1
2
3
4
1
2
3
4
5
1
2
3
4
1 2
3
4 5
→
RESET
→
OFF TIMER
→
ON TIMER
PROGRAM TIMER
(
OFF
←
ON, OFF
→
ON)
←
Press the START/STOP button to start the air conditioner, and then proceed as follows.
Press the START/STOP button to start the air conditioner, and then proceed as follows.