Airspan FlexNET ASN-700 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 76

background image

605-0001-801 FlexNET Link Products

Power cabling using PSU-3 power supply

The PSU-3 power supply unit can feed one ASN-700/800 base station product. The power

supply is an external unit designed for operation in outdoor environment. The supply voltage of

the power supply is 24 VDC. The power supply unit provides RS-485 connector for remote

management of the base station unit. RS-485 pins must be wired from the base station unit to

power supply if RS-485 remote management is needed. Wiring can be done by 4-wire power
cable.

RS-485 is a data communications interface standard approved by the Electronic Industries

Association (EIA) for multipoint communications with serial devices. It is ideal for industrial

applications due to its noise immunity.

The transmitted data is represented by voltage differences between the two wires of the power
cable. RS-485 requires specific serial port hardware that supports RS-485 voltages and

conventions.

Detailed cabling instructions are in Appendix 1.

Power cabling using PSU-2 power supply (accessory)

The PSU-2 power supply is an external unit designed for operation in outdoor environment. The

PSU-2 power supply unit can feed up to two ASN-700/800 products. The supply voltage of

power supply is 12 VDC. The power supply unit has an inbuilt sealed lead-acid rechargeable
battery to ensure at least a few minutes of operation when the main supply voltage is lost. This

battery back-up time depends on the condition of the battery. It is recommended to replace the

battery from time to time, e.g. once a year. This replacement time depends on ambient

temperature of the power supply unit.

Ethernet cabling

The maximum length of Ethernet cabling without repeaters or amplifiers is 100 meters (330

feet). Ethernet cabling must fulfil CAT5 category FTP outdoor cable specifications. Detailed
cabling instructions can be found in Appendix 1.

Protective connector cover

If the Ethernet connectors are not used you must cover the connectors by a protective

cover. The ASN-700/800 is shipped with protective covers on both Ethernet connectors by

default.

Applying coax seal tape

When using the unit with external antennas, you must weather seal the N connectors using seal

tape. N connectors that are not properly sealed permit moisture to enter the connection, which

leads to performance degradation or coverage problems.

8

«
...
12
13
14
15
16
...
»

Содержание FlexNET ASN-700













































































Отзывы:

Нет отзывов

Похожие инструкции для FlexNET ASN-700

Бренд: Patton electronics Страницы: 8

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: ZoneVu Страницы: 15

Бренд: Top Страницы: 21

Бренд: Idis Страницы: 16

Бренд: Steren Страницы: 130

Бренд: Lanner Страницы: 99

dLAN 200 AVsmart+

Бренд: Devolo Страницы: 2

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

Бренд: Billion Страницы: 14

Бренд: QNAP Страницы: 68

Бренд: ROBOfiber Страницы: 2

Бренд: D-Link Страницы: 118

Бренд: D-Link Страницы: 121

Бренд: D-Link Страницы: 240

Бренд: Siemens Страницы: 10

Бренд: Siemens Страницы: 50

RUGGEDCOM RM1224

Бренд: Siemens Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды