Airspan AS MAX EasyST 4.9 Скачать руководство пользователя страница 17

Страница: 17 / 50

PHYSICAL DESCRIPTION

This section describes the EasyST's physical description:

  Physical Dimensions
  Ports
  LEDs
  LED Button (Planned for Future)

Physical Dimensions

The physical dimensions of the EasyST are listed in the table below:

Parameter

Value

Dimensions

(height x width x

depth)

With clip-on antenna: 130 x 145 x 145 mm (5.12 x

5.7 x 5.7 inches)

Without clip-on antenna: 30 x 145 x 145 mm (1.18

x 5.7 x 5.7 inches)

Weight

With clip-on antenna: 0.426 kg (approximate)
Without clip-on antenna: 0.3 kg (approximate)

Ports

The EasyST provides various ports on its top, bottom, and side panels, as described in the table

below:

Panel

Port

Interface

8-pin RJ-45

10/100BaseT Ethernet LAN

Side

DC power jack

6 VDC power (supplied by AC/DC power adapter)

6-pin header

Integrated Antenna Controller for attaching clip-on

antenna (determines active antenna--1 out of 4)

Top

(cover

exposed)

MCX jack

Clip-on antenna

30-pin IDC socket

Plug-in extension board for the following interfaces

planned for future

802.11 Wi-Fi and LAN switch
VoIP and Battery Backup

(The

IDC socket accepts flat cables)

Bottom

SIM

Authentication support (planned for future)

The figures below display the EasyST ports, which are located on the top (with the clip-on antenna

removed) and bottom panel respectively.

Содержание AS MAX EasyST 4.9



















































Результаты поиска

Содержание AS MAX EasyST 4.9

Отзывы:

Бренды по названию

Популярные бренды

Airspan AS MAX EasyST 4.9, Руководство по установке оборудования

Результаты поиска

Содержание AS MAX EasyST 4.9

Отзывы:

Бренды по названию

Популярные бренды