Airspan AIRSTAR 1200 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 36

Airspan AIRSTAR 1200 Скачать руководство пользователя страница 11

AirStar 1900/1200 5G Sub-6 GHz Full gNB/RDU

2T2R Indoor Radio Unit – Installation Guide

© Copyright Airspan Networks Ltd., 2022

P/N:

DUG01084

Rev. A0.6, Mar 2022

6

1

Introduction

This section provides a descriptive overview of the installation of Airspan’s AirStar 1900/1200 and its
place in the Airspan product suite.

This document is intended for readers with 5G working knowledge.

All information in this document is for general information only, and is subject for change without
notice.

1.1

AirStar 1900/1200 5G Sub-6Hz

The AirStar1900/1200 is 5G-NR, sub-6 GHz indoor solution that’s part of the OpenRANGE product line.
It consists of both a radio unit (RU), distributed unit (DU) and in a compact unit (CU). It either can
operate as a full gNB solution, or can be based on 3GPP split 2 architecture (SW Roadmap) - thus,
allowing network adaptability for operators. The AirStar1900/1200 delivers enhanced, indoor to
indoor and indoor to outdoor network coverage and capacity.



For management please refer to the system Commissioning Manual.

Figure 1: AirStar 1900/1200 5G Sub-6Hz

«
...
9
10
11
12
13
...
»

Содержание AIRSTAR 1200





































Отзывы:

Нет отзывов