background image

4

Introduction

Thank you for purchasing an Airmar solid-state sensor. The compact housing is 
waterproof with a single removable cable. The H2183 is actually three sensors in 
a single unit—a three-axis magnetic compass, a three-axis accelerometer, and a 
three-axis rate gyro. Data is simultaneously output in digital NMEA 0183 and 
NMEA 2000

®

 formats.

1. Only available if magnetic variation is available from an external device such as a GPS.

Features

• Fast response time
• Stable and accurate data in dynamic conditions
• Can be programmed to compensate for an installation that is not aligned to the 

front of the vehicle/bow of the boat and/or level

• Can be calibrated to compensate for magnetic deviation caused by ferrous 

metals and other electro-magnetic fields

• Waterproof housing
• Waterproof cable system
• Bracket or flush mount

Functions & Outputs

H2183

Magnetic compass heading

Heading relative to true north 

1

Rate of Turn

Angle of pitch and roll

Rate of pitch & roll

NMEA 0183: RS-422

Optional

NMEA 0183: RS-232

Optional

NMEA 20000; CAN

IMPORTANT: Please read the Owner’s 

Guide completely before proceeding.

Содержание H2183

















Отзывы: