AirLive G.DUO Скачать руководство пользователя

Страница: 119 / 139

12. Frequent Asked Questions

AirLive G.DUO User’s Manual

110

In this chapter, we will address some frequent asked questions about G.DUO

Question

Why is there no password protection for G.DUO?

Answer

: By default, the password protection is turned off for G.DUO. Please go to

“System Configuration -> Password Settings”, then enter a new set of
username and password to turn it on.

===================================================================

Question

I forgot my password or the IP address of G.DUO.

Answer

: Please restore your settings to default by press the reset button for more than

7 seconds. You should be able to find your G.DUO at 192.168.1.254 with
password “airlive”.

====================================================================

Question

Why am I not getting good performance when I am running 2 radios at the

same time?

Answer

: G.DUO’s 2 radios system require special attention in regards to mutual

interference. It is recommended that you take the following steps to ensure
best performance for a 2-radio system

Please make sure the 2 radios’ channels are set as far apart as possible.
For example, one at channel 1 and one at channel 11

Please adjust the angle of the antenna or the orientation of the AP to get
the best performance. The best performance is about 30 degree from
horizontal as indicated in the graph below.

Do not increase the TX output power unless one or both radio are using
directional antenna.

12.

Frequent Asked

Questions

Содержание G.DUO












































































































































Результаты поиска

Содержание G.DUO

Отзывы:

Похожие инструкции для G.DUO

Бренды по названию

Популярные бренды

AirLive G.DUO, Руководство пользователя

Результаты поиска

Содержание G.DUO

Отзывы:

Похожие инструкции для G.DUO

Бренды по названию

Популярные бренды