AirLive ARM-204 Скачать руководство пользователя страница 8

Страница: 8 / 77

1.4. Hardware

Placement

1.4.1. Rear Panel

1) Reset

The Reset button can be used to reset the router or restore to factory defaults.

If problems occur with your router, press the router’s reset button with a

pencil tip (for less than 5 seconds) and the router will re-boot itself,

keeping your original configurations.

If problems persist or you experience extreme problems or you forgot

your password, press the reset button for longer than 5 seconds and the

router will reset itself to the factory default settings (

warning

: your

original configurations will be replaced with the factory default settings)

2) Power Jack

Please plug the power adapter attached with the ADSL Router to the power

jack. The power adapter is 12VDC, 1A.

3) Local Area Network (LAN)

The router’s 4 LAN ports are where you connect your LAN’s PCs, printer

servers, hubs and switches etc.

4) ADSL

Содержание ARM-204














































































Результаты поиска

Содержание ARM-204

Отзывы:

Бренды по названию

Популярные бренды

AirLive ARM-204, Руководство пользователя

Результаты поиска

Содержание ARM-204

Отзывы:

Бренды по названию

Популярные бренды