Airlink101 AP421W Скачать руководство пользователя | Manualshive

Страница: 36 / 40

background image

36

7.5 Advanced Wireless

The Advanced Wireless page allows you to customize data transmission settings. In
most cases, the advanced settings on this page should remain at their default values.

Beacon Interval:

The default value is

100

. Enter a value between 20 and 1000

milliseconds. The Beacon Interval value indicates the frequency interval of the beacon.
A beacon is a packet broadcast by the Access Point to synchronize the wireless
network.

RTS Threshold:

This value should remain at its default setting of

2347

. The range is

256-2347 bytes.

Should you encounter inconsistent data flow, only minor modifications are
recommended. If a network packet is smaller than the preset RTS threshold size, the
RTS/CTS mechanism will not be enabled. The Access Point sends Request to Send
(RTS) frames to a particular receiving station and negotiates the sending of a data
frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS)
frame to acknowledge the right to begin transmission.

«
...
34
35
36
37
38
...
»

Содержание AP421W









































Отзывы:

Нет отзывов

Похожие инструкции для AP421W

Бренд: H3C Страницы: 42

DWL-2700AP - AirPremier Outdoor Wireless Access...

Бренд: D-Link Страницы: 70

DWL-2200AP - AirPremier - Wireless Access...

Бренд: D-Link Страницы: 58

Бренд: Zenitel Страницы: 29

Бренд: Fortinet Страницы: 11

Бренд: FUNAI Страницы: 7

Бренд: Digi Страницы: 9

Бренд: Linksys Страницы: 124

Бренд: iBall Baton Страницы: 62

Бренд: AmbiCom Страницы: 1

Бренд: EnGenius Страницы: 53

Бренд: EnGenius Страницы: 66

Бренд: EnGenius Страницы: 45

Бренд: EnGenius Страницы: 60

Бренд: EnGenius Страницы: 75

Бренд: EnGenius Страницы: 84

Бренд: EnGenius Страницы: 86

Бренд: EnGenius Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды