background image

 

WHEN TRANSPORTING EQUIPMENT

  •  Transport with fuel tank EMPTY or with fuel shut-off  

    valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH 

FUEL IN TANK

  •  Store away from furnaces, stoves, water heaters and  

    other appliances that have pilot lights or other ignition  

    source. They can ignite gasoline vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

  •  If there is natural or LP gas leakage in area, do not  

    start engine.

  •  Do not use pressurized starting fluids because vapors  

    are flammable.

Rapid retraction of starter cord (kickback) will pull 

hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

 •  When starting engine, pull cord slowly until resistance is  

   felt, then pull rapidly.

•  Remove all external equipment/engine loads before starting  

   engine.

•  Direct coupled equipment components such as, but not  

   limited to, blades, impellors, pulleys, sprockets, etc. must  

   be securely attached.

Rotating parts can contact or entangle hands, feet, 

hair, clothing or accessories.

Traumatic amputation or severe laceration can result.

•  Operate equipment with guards in place.

•  Keep hands and feet away from rotating parts. 

•  Tie up long hair and remove jewelry.

•  Do not wear loose fitting clothing, dangling drawstrings or  

   items that could become caught.

Engines give off carbon monoxide, an odorless, 

colorless, poison gas.

Breathing carbon monoxide can cause nausea, 

fainting or death

.

•  Start and run engine outdoors.

•  Do not start or run engine in enclosed area, even if doors or  

   windows are open.

Safety Warnings

Running engines produce heat. Engine parts, 

especially mufflers, become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, 

etc. can catch fire.

•  Allow muffler, engine cylinder and fins to cool before  

   touching.
•  Remove accumulated combustibles from muffler area and  

   cylinder area.
•  Install and maintain in working order a spark arrester    

   before using equipment on forest covered, grass covered  

   and brush covered unimproved land. The state of  

 

   California requires this (Section 4442 of the California  

   Public Resources Code). Other states may have similar  

   laws. Federal laws apply on federal land.

Unintentional sparking can result in fire 

or electric shock.

Unintentional start up can result in entanglement, 

traumatic amputation, or lacerations.

BEFORE PERFORMING ADJUSTMENTS OR 

REPAIRS

•  Disconnect spark plug wire and keep it away from  

   spark plug.

 •  Disconnect battery at negative terminal (only  

 

   engines with electric start).

WHEN TESTING FOR SPARK

 •  Use approved spark plug tester.

 •  Do not check for spark with spark plug removal.

6   

Содержание Spray & Stripe 3600

































Отзывы: