Getting Started – Plug in to a standard (120V AC)
electrical outlet. The digital clock on the LED Display will
flash 4 times. Then, showing the current time, the unit enters
a standby mode. To change the time in the standby mode:
Press the “Clock” button for about 3 seconds-you will hear
a beep and the hour will flash. Press the “Hr/Min Set” button
to change the hour; quickly press the “Clock” button once
more. The minutes on screen will flash, again press the
“Hr/Min Set” button to change the minutes. The set time
flashes for 3 seconds and then is saved automatically.
ON/OFF – From standby mode, press the “On/Off” button
once and the “Operating” indicator will turn on and the cur-
rent ambient humidity will be displayed. Mist may not appear
immediately; allow up to 15 minutes for the water in the tank
to transfer to the base. Timer Functions: The Delay Start and
Auto-Off buttons allow you to set the humidifier to turn ON
and OFF automatically as desired.
Delay Start – The Delay Start allows you to program the unit to turn ON automatically. This
feature uses the clock function and is programmable to the hour and minute. To use, press
the “Delay Start” button once; you will see 0:00 illuminated on the display. The hour will
flash-press the “Hr/Min Set” button to change the hour, quickly press “Delay Start” again
and the minutes will flash, use the “Hr/Min Set button to change the minutes. The set time
flashes for 3 seconds and is saved automatically. The LED Display will read “Timer” “Delay
Start”. To check the set time, press the “On/Off” button and quickly press “Delay Start”. To
use the unit in Manual Mode you will need to clear the Delay Start setting, to do so press the
“Delay Start” button for about 3 seconds, until you hear a beep
.
Auto-Off – The Auto-Off feature allows you to run the humidifier now and set it to turn OFF
at a specific time automatically. To use, press the “Auto-Off” button once; you will see 0:00
illuminated on the display. The hour will flash-press the “Hr/Min Set” button to change the
hour, quickly press “Auto-Off” again and the minutes will flash, use the “Hr/Min Set button
to change the minutes. The set time flashes for 3 seconds and is saved automatically. The
LED Display will read “Timer” “Auto-Off”. To check the set time, press the “Auto-Off” button.
To use the unit in Manual Mode you will need to clear the Auto-Off setting, to do so press
the “Auto-Off” button for about 3 seconds, until you hear a beep. NOTE: You can use the
Delay Start and Auto-Off functions together on this fully programmable LED Display to
program the humidifier to turn ON and turn OFF at your desired times
Mist Output – When you turn the unit ON, it will default to the lowest mist setting. Pressing the
“Mist” button will increase the output. Press once for Medium, twice for High, three times for
Supreme, four times for the Turbo Setting. Pressing the Mist button a fifth time will bring the unit
back to Low. NOTE: Turbo setting is intended for those wanting a more powerful mist and
works best while the Extension Nozzle is being used. The Turbo setting will operate for 40
minutes and will then go to the Supreme Mist Setting. User must wait 20 minutes before
Turbo setting can be used again.
5
Remote
Control
Be sure to remove
the clear pull tab
before using the
remote.The func-
tions on the Remote
Control mirror those
on the humidi-
fier. When using the
Remote Control,
you can control the
humidifier from your
desired location.
Operating Instructions
WARNING: DO NOT operate the humidifier without water in the tank.
WARNING: NEVER lift the tank off the Base while the unit is operating.
Humidistat – By using this feature the humidifier will automatically monitor and
control the humidity level according to your desired setting. Once the desired humidity level
is reached the mist will shut OFF until the humidity drops below the setting and then the mist
will turn back ON automatically to maintain the humidity level desired. To set this feature
press the “Humidistat” button to your desired setting. Settings range from 40%-95% RH
(Relative Humidity) in 5% RH increments. A 40%-60% Relative Humidity is recommended.
Once you set your desired humidity, the number will blink three times and then the display
will revert back to the Relative Humidity. To view the set humidity level, press the Humidistat
button once.
Beep/Dim – Default function: the humidifier is factory set to beep when changing settings
and to alert when the humidifier is out of water; also the LED Display and Mood Light are set
to be illuminated. To disable one or more of these settings: Press “Beep/Dim” once to disable
all sound (“Beep Off” on the display will flash 3 times and then will remain on the display to
indicate the sound is OFF); press the button twice to turn the LED Display OFF; press a third
time to turn the Mood Light OFF. Pressing the “Beep/Dim” button a fourth time will bring the
unit back to the default function
.
Low Water – When the tank is out of water the “Waterless” indicator will appear on the
display; you will hear 3 beeps and the automatic safety shut-off will turn the Ultrasonic
Nebulizer and unit OFF. NOTE: You can disable the beep by pressing the “Beep/Dim”
button once; re-enable by pressing the button three more times.
