background image

 

 

Airflow Vector Pty Ltd 

 

 

4 Collins Rd, DROMANA VIC. 3936 

  

AUSTRALIA 

 

 

Ph: +61 3 5987 3733 

 

 

www.airflowvector.com 

 
SD009US (S009 Instructions booklet).doc 

21 March 2011 

Page 1 of 16 

 

 

\\Server\d\AirflowSnorkels\Products\Snorkels\S009\SD009US (S009 Instructions booklet).doc

 

 

Instructions to fit the Snorkel Kit S009 

for the Chevrolet Silverado or GMC Sierra 

1.0 Introduction 

Airflow Vector Pty Ltd thanks you for your purchase and the trust you put in our 
products. 
We strive to supply our customers with the highest quality equipment based on 
the most efficient design and best styling. We are confident that you will enjoy 
using our Snorkel system.  
It should improve the power of your vehicle as well as reduce its fuel 
consumption. 

 

1.1 General instructions 

Follow carefully the instructions listed on these pages and use the template 
provided, do not over tighten bolts. Do not use silicone on any connections, 
use mastic. 
Ensure that safe work practices are followed when installing your Airflow 
Snorkel. Protective ear and eye wear should be worn at all times when using 
power tools.

 

 

1.2 Disclaimer 

It is highly recommended that installation is undertaken by a qualified 
mechanic or body shop. Airflow Vector will not be held responsible for any 
damage incurred through incorrect fitment of the templates and workmanship. 
It is the responsibility of the fitter to ensure that particular care is taken when 
assembling the Snorkel kit to the vehicle as it may cause damage to the 
windscreen and or electrical components. Safe work practices must be used at 
all times when undergoing installation. 
 
We guarantee Airflow Vector’s kits against manufacturing defects as long as 
proof of purchase can be established.  
 
All models produced by Airflow Snorkels are verified to suit right hand drive 
vehicles according to Australian specifications. Variations in vehicle 
specifications may occur in other markets.  
If you're in doubt about the product suitability, please forward a photograph of 
the engine bay, air filter housing and of the vehicle at frontal/side position to 

[email protected] 

 

 

Содержание S009

















Отзывы: