Manual
of
Brushless Motor Speed Controller
HW-SM003ENG-20120606 Page 2 of 2
-
Trouble Shooting
Trouble
Possible Reason
Action
After power on, motor does not work, no
sound is emitted
The connection between battery
pack and ESC is not correct
Check the power connection.
Replace the connector.
After power on, motor does not work,
such an alert tone is emitted:
“beep-beep-, beep-beep-,beep-beep-”
(Every
“beep-beep-” has a time interval
of about 1 second)
Input voltage is abnormal, too high
or too low.
Check the voltage of battery pack
After power on, motor does not work,
such an alert tone is emitted:
“beep-, beep-, beep- ”(Every “beep-” has
a time interval of about 2 seconds)
Throttle signal is irregular
Check the receiver and transmitter
Check the cable of throttle channel
After power on, motor does not work,
such an alert tone is emitted:
“beep-, beep-, beep-” (Every “beep-” has
a time interval of about 0.25 second)
The throttle stick is not in the
bottom (lowest) position
Move the throttle stick to bottom position
After power on, motor does not work, a
special tone
“
” is emitted after 2
beep tone (beep-beep-)
Direction of the throttle channel is
reversed, so the ESC has entered
the program mode
Set the direction of throttle channel correctly
The motor runs in the opposite direction
The connection between ESC and
the motor need to be changed.
Swap any two wire connections between ESC and
motor
Program the ESC with your transmitter (4 Steps):
Note:
Please make sure the throttle curve is set to 0 when the
throttle stick is at bottom position and 100% for the top position.
1. Enter program mode
2. Select programmable items
3. Set item
’s value (Programmable value)
4. Exit program mode
1. Enter program mode
1)
Switch on transmitter, move throttle stick to top
position, connect the battery pack to ESC
2)
Wait for 2 seconds, the motor should emit
special
tone like “beep-beep-”
3)
Wait for another 5 seconds, special tone like
“
” should be emitted, which means
program mode is entered
4. Exit program mode
There are 2 ways to exit
program mode:
1.
In step 3, after special
tone “
”, please
move throttle stick to
the bottom position
within 2 seconds.
2.
In step 2, after tone
“beep-----beep-----”(ie.
The item #8), move
throttle stick to bottom
within 3 seconds.
3. Set item value (Programmable value):
You will hear several tones in loop. Set the value matching to a tone by moving throttle stick
to top when you hear the tone, then a special ton
e “
” emits, means the value is set
and saved. (Keeping the throttle stick at top, you will go back to Step 2 and you can select
other items; or moving the stick to bottom within 2 seconds will exit program mode directly)
Tones
Items
“beep-”
1 short tone
“beep-beep-”
2 short tones
“beep-beep-beep”
3 short tones
Brake
Off
On
Battery type
Lipo
NiMH
Cutoff mode
Soft-Cut
Cut-Off
Cutoff threshold
Low
Medium
High
Start mode
Normal
Soft
Super soft
Timing
Low
Medium
High
2. Select programmable items:
After entering program mode, you will hear 8 tones in a loop with
the following sequence. If you move the throttle stick to bottom
within 3 seconds after one kind of tones, this item will be selected.
1.
“beep”
brake (1 short tone)
2.
“beep-beep-”
battery type (2 short tone)
3.
“beep-beep-beep-” cutoff mode (3 short tone)
4.
“beep-beep-beep-beep-” cutoff threshold (4 short tone)
5.
“beep-----”
startup mode (1 long tone)
6.
“beep-----beep-” timing (1 long 1 short)
7.
“beep-----beep-beep-” set all to default (1 long 2 short)
8.
“beep-----beep-----” exit (2 long tone )
Note
: 1 long “beep-----” = 5 short “beep-”
Содержание 95A301
Страница 1: ......
