background image

Page 14

Due to continuous product research and development,
the information contained herein is subject to change without notice.

www.stoddart.com.au
www.stoddart.co.nz

Cleaning and Maintenance

•  Cleaning is recommended for health and safety purposes and to prolong the life of the unit
•  Do NOT use abrasive pads or cleaners on the stainless steel or any other metal parts of the unit
•  Do NOT use industrial chemical cleaners, caustic based cleaners or bleaches and bleaching agents, as many will damage the metals 

and plastics used on this unit

•  Do NOT remove any screws and/or panels for cleaning (unless directed)
•  This unit is NOT waterproof, do NOT hose, do NOT pour water directly onto the unit, do NOT immerse in water

•  Stainless steel exhibits good resistance to corrosion however, if not properly maintained stainless steel can rust and/or corrode
•  Any sign of mild rust and/or corrosion should be thoroughly cleaned with warm soapy water and dried as soon as possible
•  NEVER use abrasive pads or cleaners for cleaning
•  All metal surfaces should be checked while cleaning for damage, scuffs or scrapes as these can lead to rust and further damage to the 

product

•  Mild rust and/or corrosion can be treated with a commercial cleaning agent that contains citric/oxalic/nitric/phosphoric acid.

Do NOT use cleaning agents with chlorides or other harsh chemicals as this can cause corrosion.
After treatment, wash with warm (not hot) soapy water and dry thoroughly

•  Thoroughly wipe the surfaces dry after cleaning and do NOT let water pool on the unit. Check crevices and folds for pooling
•  When using, ensure all liquids and moisture is cleaned up straight away.

Food liquids such as juices from vegetables and fruits should NOT be left on preparation surfaces

•  Do NOT leave items on the stainless steel such as cutting boards, rubber mats and bottles

•  To protect the polish, stainless steel should be dried by wiping a dry soft cloth in the same direction as grained polished fi nish
•  For NON-food contact surfaces, a light oil can be wiped on the surfaces with a cloth to enhance the stainless steel surface.

Wipe in the direction of the grain

•  Some commercial stainless steel cleaners can leave residue or fi lm on the metal; this may trap fi ne particles of food on the surface, 

thus deeming the surfaces not food safe

IMPORTANT

Threaded fasteners can loosen in service. 

Regular inspection and adjustment 

should be carried out as required  

WARNING

This unit is NOT waterproof, do NOT 

hose. DO NOT pour water directly onto 

the unit. DO NOT immerse in water

IMPORTANT

Some commercial stainless steel 

cleaners leave residue or fi lm on the 

metal that may entrap fi ne particles of 

food, deeming the surface not 

FOOD SAFE

WARNING

This unit includes refrigeration 

components. 

Cold surfaces can burn DO NOT touch 

these surfaces

Cleaning

General Information

Corrosion Protection

Surface Finish

Содержание AXR.URGN.1





















Отзывы: