background image

Motor Wires

   Thread the motor wires through the 

   canopy, downrod stand cover and 

   downrod.

PAGE: 1 / 4

Installation Steps :

Hanger Pin

Lock Pin

 

INSTALLATION INSTRUCTIONS

IMPORTANT:

  BEFORE YOU BEGIN INSTALLING THE FAN, CAREFULLY READ ALL INFORMATION ON THE SEPARATE

  SHEET "SAFETY INSTRUCTIONS" AS WELL AS THE FOLLOWING "INSTALLATION INSTRUCTIONS". IF IN

  DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

  THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.

  SAVE ALL INSTRUCTIONS.

 

NOTE: The fan weight is 21.1 lb (9.6 kg). Be sure the outlet box you are using is securely attached to the building structure 

and can support the full weight of the fan. Failure to do so can result in serious injury.

Tighten the hanger bracket to the outlet

 box with 2 mounting screws. (To reduce 

 the risk of fire electric shock, or personal

 injury, mount to the outlet box marked

 "Acceptable for fan support" and use 

 mounting screws provided with the outlet

 box.)

   Hang the fan on hanger bracket, 

   and make sure the slot of hanger 

   ball is snapped into the chip of 

   hanger bracket exactly.

   Note: For slope ceiling installation, 

   make sure the slot of hanger ball 

   and the chip of hanger bracket is

   face down.

Fig.1

Outlet Box

Hanger 

Bracket

Fig.2

Turn OFF the electric power at the

main fuse or circuit breaker box. 

Remove the Lock Pin and take off 

the Hanger Pin.  

Fig.3

Insert and tighten the two Collar 

Screws. Slide Lock Pin into Hanger

Pin until it locks into position.   

Fig.6

Lock Pin

Collar Screws

Slot

Chip

Hanger Bracket

Fig.7

Insert the Downrod into the Collar.

Slide Hanger Pin through holes of

Collar and Downrod. 

Fig.5

Motor Wires

Downrod 

Downrod Stand

Cover

Canopy 

Fig.4

Hanger Pin

070421

TM

Содержание FN56305









Отзывы: