AirBench FN066784 Скачать руководство пользователя страница 16

Страница: 16 / 19

Page 16 of 19

THOROUGH EXAMINATION AND TESTING

If AirBench is used as an LEV system it must be tested at regular (normally 12 month) intervals and certificated

under the COSHH regulations. This service is available from us, or our approved testers.

Thorough examination and test should include:

Ensuring the prescribed maintenance routines are being completed and recorded within the system logbook.

Condition check of fan, filters, electrics.

Performance testing according to recommended face velocities.

Visual check that operators are working within effective area.

Visual check of effectiveness using, for example, smoke tubes.

Recommended face velocities are as follows:

Fume control: Minimum 0.5m/s

Light dust control: Minimum 1.0 m/s

Heavy dust control: 1.2

–

1.5m/s

Completion of Thorough Examination and Testing should be recorded within the system logbook.

Содержание FN066784

















Результаты поиска

Содержание FN066784

Отзывы:

Похожие инструкции для FN066784

Бренды по названию

Популярные бренды

AirBench FN066784, Эксплуатация и обслуживание

Результаты поиска

Содержание FN066784

Отзывы:

Похожие инструкции для FN066784

Бренды по названию

Популярные бренды