manualshive.com logo in svg

Airaya AI108-4958-1, Руководство пользователя и инструкция по установке

Поделиться
Скачать
Airaya AI108-4958-1 Скачать руководство пользователя страница 16

 

- 16 - 

Airaya

 – Fast and affordable outdoor wireless bridges

 

Follow these steps to install and visually align outdoor antennas: 
   

1. 

Attach the antenna to a mast or side of a building using the included 

bracket. 

 

2. 

Align the outdoor antenna horizontally: Loosen the horizontal 
adjustment bolt and nut to visually aim the antenna at the remote 
bridge. Set the appropriate horizontal angle and tighten the horizontal 

adjustment bolt and nut so that the angle is locked in place. 

 

3. 

Align the outdoor antenna vertically: Loosen the vertical adjustment 
bolt and nut on the mounting bracket and point the antenna towards 
the remote end point. Set the appropriate elevation angle and tighten 
the alignment bolts so that the angle is locked in place. 

 

4. 

Secure the cable along the mast between the outdoor antenna and the 
indoor bridge inside your building. 

Note:

 We recommend that you 

secure the entire cable to the mast at 10-foot intervals. 

 

5. 

Repeat steps one through four for each remote location outdoor 
antenna. 

 

6. 

Use the real-time Signal Strength Monitor

 

to fine-tune received signal 

strength (RSSi) between bridges. This tool is designed to maximize the 

throughput of your new WirelessGRID link by providing the highest 
possible signal strength across a wireless path. See the section on 

“Antenna Alignment and Link Monitoring Tool”

 for instructions. 

 

 
 

TIP 

If this is your first installation of an AIRAYA link, AIRAYA recommends that 
you perform the bench test procedure in Appendix A before deploying the 
product.  This will ensure that bridges are functioning properly and fully 
configured, and will allow you to become familiar with the tools for aligning 
antennas and optimizing throughput before you get into the field. 

 

Содержание AI108-4958-1





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды