ATTENTION! Lamp and remote in Airam LED WIRELESS
Starter Set are paired together already at the factory and
are ready to use out of the box.
1. Switching on/off
Short press ON/OFF button to turn on and off the lamps that are
paired with Airam LED WIRELESS remote.
To maintain the best functionality, always keep mains connected to the
lamp and only switch it on/off using the Airam LED WIRELESS remote.
2. Dimming
1. Press Dim down -button to dim down the lamps that are paired with
Airam LED WIRELESS remote.
2. Press Dim up -button to brighten the lamps that are paired with Airam LED
WIRELESS remote.
Short presses will dim up/down in small steps. Press and hold to dim up/
down seamlessly.
3. Lamp pairing
Follow below instructions only in case you buy a new Airam LED WIRELESS
Extension Lamp or if existing Airam LED WIRELESS lamp is reset to factory
default.
1. Turn on the lamp you want to pair with the Airam LED WIRELESS remote.
2. Bring the remote <10 cm from the lamp you want to pair.
3. Press ON/OFF and Dim down buttons simultaneously and keep them
pressed. After 6 seconds, the lamp blinks two times. You can release the
buttons after the lamp stops blinking. The lamp is now paired with the
remote.
You can pair up to 16 lamps to the Airam LED WIRELESS remote.
4. Lamp unpairing
1. Turn on the lamp you want to unpair from the Airam LED WIRELESS
remote.
2. Bring the remote <10 cm from the lamp you want to unpair. If you have
more than one lamp close to each other (<50 cm), it is recommended
to switch off mains from the nearest lamps you don’t want to unpair.
Otherwise you could accidently unpair a wrong lamp.
3. Press ON/OFF and Dim up buttons simultaneously and keep them pressed.
After 6 seconds, the lamp dims down and blinks two times. You can release
the buttons after the lamp stops blinking. The lamp is now unpaired with
the remote.
4. If you want to re-pair the lamp you need to cycle the mains first, then
follow the lamp pairing instructions on section 3.
5. Quick scene
1. Set the dimming level you want with Dim Up and Dim Down buttons.
2. Press the Quick scene –button and keep it pressed until lamp blinks. The
set dimming level is now saved.
3. Restore the saved dimming level by short pressing the Quick scene button.
6. Resetting remote
1. Press Reset-button for 3 seconds.
2. Remote is now reset to factory default. All the lamps that were paired to it,
are now unpaired.
7. Resetting lamp
1. Turn the lamp mains on.
2. Cycle the mains 6 times: 2s off, 1s on, 2s off, 1s on, 2s off, 1s on, 2s off, 1s on,
2s off, 1s on, 2s off, 1s on.
3. Keep the mains on and the lamp blinks two times. The lamp is now reset
and it is unpaired from the remote.
4. If you want to re-pair the lamp you need to cycle the mains first, then
follow the lamp pairing instructions on section 3.
ON
OFF
10s
2s
1s
2s
1s
2s
1s
2s
1s
2s
1s
2s
10s
6x
Airam Electric Oy Ab, Sementtitehtaankatu 6, FI-04260 Kerava • www.airam.fi
Indicator
ON/OFF
Dim up
Dim down
Quick scene
37 mm
88 mm
LED
WIRELESS
USER GUIDE
ZB 3.0
Reset button
CR2450 lithium
coin cell battery
NR
CODE
GTIN
E-NR
4713404 A7UAFH
4,8W/827 GU10 PAR16 36D 800CD
6435200235367
8220059
4713405 A7UAFI
9W/827 E27 A60 806LM
6435200235381
8220060
4713406 A7UAFJ
4,8W/827 GU10 36D+CONTR.UNIT
6435200235404
8220061
4713407 A7UAFK
9W/827 E27 A60+CONTR.UNIT
6435200235428
8220062
4713806 A7UAFL
LED OP C38 ZB 5,3W/827 E14 BX
6435200250674
8294419
4713808 A7UAFM
LED OP C38 ZB 5,3W/827 E14+CTR.U BX
6435200250704
8294420
47W18
