manualshive.com logo in svg

Air Monitor Corporation AMC POWER VELTRON DPT, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Air Monitor Corporation AMC POWER VELTRON DPT Скачать руководство пользователя страница 18

VELTRON DPT

Air Monitor Corporation

116-009-70.P65 (09/18/09)

VELTRON DPT - IO&M Manual

14

7 – MAINTENANCE

SECTION 7 – MAINTENANCE

The VELTRON DPT is a solid state device having no mechanical parts requiring special periodic maintenance.  The
following maintenance steps are not requirements, but guidelines for establishing a maintenance program for your
specific installation.

Operating experience should be used to set frequency of specific types of maintenance.

7.1 – CLEANLINESS

– Verify condensation (or other sources of liquids) are not present inside the VELTRON DPT.

7.2 – MECHANICAL

– Verify pressure signal connections are secure.
– Inspect pressure signal lines for any cracks or leaks.
– Verify mounting hardware is secure.

7.3 – ELECTRICAL

– Periodically inspect all wiring to the VELTRON DPT for good connections and absence of corrosion.

7.4 – CALIBRATION

– VELTRON DPT should have calibration verified annually as a minimum.

Содержание AMC POWER VELTRON DPT






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды