manualshive.com logo in svg

Air Live POE-FSH2422G-250, Руководство пользователя

Поделиться
Скачать
Air Live POE-FSH2422G-250 Скачать руководство пользователя страница 16

2. Installation of the Switch 

AirLive POE-FSH2422G-250 User’s Manual 

 

11

2.5 Desktop Installation 

 

The POE-FSH242G-250 PoE Switch has four rubber pads attached on each corner of its 

underside. These pads serve as cushioning against vibration and prevent the switch from 

sliding off its position.    They also allow adequate ventilation space when you place the 

switch on top of another device. 

 

 

 

 

„

  The location you choose to install your switch and the way you configure your network 

may greatly affect its performance.    Please see the previous section for “installation 

site” preparation. 

„

  Do not place more than 3kg (6.6lbs) of weight on the top of the switch. 

„

  Leave at least 10cm (4 inch) of space around the switch to allow proper heating 

dissipation.  

 

 

2.6 Cabling Requirements 

 

For 100BASE-TX and 1000Base-T ports 

 

The 24 RJ-45 station ports and the 1000Base-T ports of the optional Gigabit-Copper 

module require Cat. 5 twisted-pair UTP/STP cable for connection. When configuring within 

the 10/100/1000BASE-T cabling architecture, the cable distance should be within 100m. 

 

Содержание POE-FSH2422G-250




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды